Products
14″ Galvanized Tire & Wheel ST205/75R14 D Load Range
$165.00
Brand Com-Fab
General
Karrier ST205/75R14 D Load Range 14″ Galvanized Tire & Wheel 65 psi
This item is used on our PT-2628 Trailer Models, but is also an upgradable option for all Pontoon Trailer Models. Speed rating is 81 mph.
MODEL: CFT175DLRD-G
Used on
Upgrade for
14″ Galvanized Winch Assembly w/ RAM 600
$114.99
Brand Com-Fab
This product is sold out
General
14″ Galvanized Winch Assembly w/ RAM 600 lb Winch
This assembly includes a 14" Galvanized Winch Post, a RAM 600 lb Capacity Crank Winch, a Winch Poly Bow Roller Assembly, and a Galvanized Winch Assembly Mounting Kit.
Mounting Hardware Includes:
4 – 3/8″-16 Galvanized Tri-Lock Hex Nuts
MODEL: CFWNCH800G
Used on
PWT-800G
14″ Galvanized Winch Post
$50.00
Brand Com-Fab
General
14″ Galvanized Winch Post
This item is used as part of 14" Galvanized Winch Assemblies for Single Galvanized PWT Trailers.
14" Galvanized Winch Assembly w/ DL900 lb Winch
14″ Galvanized Winch Assembly w/ RAM 600 lb Winch
MODEL: CFWNCHPOST-1000G
Used on
14″ Galvanized Winch Assembly w/ DL 600
$130.00
Brand Com-Fab
General
14″ Galvanized Winch Assembly w/ DL 600 lb Winch
This assembly includes a 14" Galvanized Winch Post, a Dutton-Lainson 600 lb Capacity Crank Winch, a Winch Poly Bow Roller Assembly, and a Galvanized Winch Assembly Mounting Kit. When mounted, the standard height for the bow roller is 12", but it can be adjusted to accommodate your particular boat.
Mounting Hardware Includes:
4 – 3/8″-16 Galvanized Tri-Lock Hex Nuts
MODEL: CFWNCH1000G
Used on
15' 4-Pin Wire Harness Assembled w/ Protective Sleeve
$12.75
Brand Com-Fab
General
15' 4-Pin Wire Harness Assembled w/ Protective Sleeve
The wiring is pulled through the PWT-800 trailer frame to provide connection between the lighting and the vehicle. It connects to the vehicle with a 4-Pin Male Connector. This item comes with a 3/8 20" Protective Sleeve and 30" Ground with 1/2" ring terminal.
MODEL: CFWH14
Used on
1500 lb Black Powder Coated PWC Trailer Axle w/ 545 Hubs and Springs HF 50.5 SC 41.18
$250.00
Brand Com-Fab
General
1500 lb Black Powder Coated PWC Trailer 545 Axle w/ Hubs and Springs
*NOTE: if your trailer is older than 2006, call before ordering to ensure you receive the correct axle.*
Materials Include:
1 - 44.5" x 1.5" x 1.5" x 11 Gauge Black Powder Coated Axle Tubing
2 - Black Powder Coated 5-Bolt Hub Assembly
2 - 3-Leaf Slipper Springs (750 lb)
This item is mounted to the PWT-1000B, and the PWT-1100B with a Black Powder Coated Axle Mounting Kit.
MODEL: CFAXLE1500B
Specifications
Tubing: 1.5" Black Powder Coated Square Axle
Load Rating: 1500 lb
Hub Face: 50.5"
Spring Center: 41.19"
Overall Length: 56"
Bearing Size: 1-1/16"
Used on
1500 lb Galvanized PWC Trailer Axle w/ 545 Hubs and Springs HF 50.5 SC 41.18
$300.00
Brand Com-Fab
General
1500 lb Galvanized PWC Trailer Axle w/ 545 Hubs and Springs
*NOTE: If your trailer is older than 2006, call before ordering to ensure you receive the correct axle*
Materials Include:
1 - 44.5" x 1.5" x 1.5" x 11 Gauge Galvanized Axle Tubing
2 - Galvanized 5-Bolt Hub Assembly
2 - 3-Leaf Slipper Springs (750 lb)
This item is mounted to the PWT-1000G, and PWT-1100G trailer models with a Galvanized Axle Mounting Kit.
MODEL: CFAXLE1500G
Specifications
Tubing: 1.5" Galvanized Square Axle
Load Rating: 1500 lb
Hub Face: 50.5"
Spring Center: 41.188"
Overall Length: 56"
Bearing Size: 1-1/16"
Used on
1500 lb Side Crank Swivel Jack - Dutton-Lainson
$120.00
Brand Dutton Lainson
General
1500 lb Side Crank Swivel Jack - Dutton-Lainson
- Dutton-Lainson swivel marine tongue jack for boat and other trailer applications
- 1,500 lb. capacity
- 24-3/4" maximum tongue height
- Side wind handle with extra heavy screw drive and ergonomic handle grip
- Heavy duty polypropylene 8" diameter slotted wheel resists flat spots and cold weather cracking
- Zinc plated finish for additional rust resistance and longer life
- Easily swivels up for towing or down for stowing and locks in place in either position
- Reinforced wheel bracket for additional strength
- Includes all necessary bolt-on mounting hardware
- Made in the U.S.A.
Dutton-Lainson Model: 6850
MODEL: CFJACKSIDE-6850
Used On
PT-2224
PT-2426
PT-2628
17' 4-Pin Wire Harness Assembled w/ Protective Sleeve
$14.50
Brand Com-Fab
General
17' 4-Pin Wire Harness Assembled w/ Protective Sleeve
The wiring is pulled through the trailer frame to provide connection between the lighting and the vehicle. It connects to the vehicle with a 4-Pin Male Connector. This item comes with a 3/8 20" Protective Sleeve and 30" Ground with 1/2" ring terminal.
MODEL: CFWH16
Used on
192″ Black Flex Hose Male-Male Brake Line - Dexter
$49.99 $35.00
Brand Com-Fab
General
192″ Black Flex Hose Male-Male Brake Line - Dexter
This item is optional on select PT-1618 and PT-1820 models only.
For use with:
– Banjo Fitting Base
– Square Banjo Fitting Bolt
– Black O-Ring
– Copper Banjo Fitting Washer
TIE DOWN MODEL: #46238-192
MODEL: CFBRKELINE-192(BLK)
Used on
192″ Grey Poly Flex Male-Male Brake Line - Dexter
$59.99 $35.00
Brand Com-Fab
General
192″ Grey Poly Flex Male-Male Brake Line - Dexter
This item is optional on select PT-1618 and PT-1820 models only.
For use with:
– Banjo Fitting Base
– Square Banjo Fitting Bolt
– Black O-Ring
– Copper Banjo Fitting Washer
TIE DOWN MODEL: #46219-192
MODEL: CFBRKELINE-192(GREY)
Used on
2 Capacity Canoe/Kayak Conversion Kit
$339.99
Brand Com-Fab
General
2 Capacity Canoe/Kayak Conversion Kit
Universal canoe/kayak trailer conversion kit for up to 2 canoes or 2 kayaks without plastic protective covering.
One size fits all trailer kit:
- Designed to hold 2 kayak/canoes
- Adjustable crossbeam placement to fit a wide range of needs and preferences
- Fits on 1.5", 2", 3" rectangular and/or square tubing where applicable
- 2x2x11 gauge upright bracing for universal fit
- 2x2x14 gauge cross braces
This is a conversion kit only and requires a trailer to mount.
Click the following link for Assembly Instructions
https://cdn.shopify.com/s/files/1/1557/3371/files/Canoe_Kayak_Kit_Assembly_Instructions.pdf
Specifications
Kayak Setup - CFKIT-KAY(2)
- 2x 24" Uprights
- 2x 60" Crossbeams with Strap Assist and End Caps
- 2x Mounting Bracket - 2" Channel w/ 1/2" Hexagonal Holes
- 4x Zinc Bolt and Nut to Tighten Crossbeam to Mounting Bracket
- 4x Zinc U Bolts with Washer and Nut for Securing Crossbeams
- 4x Galvanized U Bolts with Washer and Nut for Securing Uprights to 1.5" & 2" Tubing
- 4x Galvanized U Bolts with Washer and nut for Securing Uprights to 3" wide Tubing
- 4x Turned Eye Bolts for use with Tie Downs
- 8x Galvanized Lock Nuts for locking in Eye Bolts
Canoe Setup - CFKIT-CAN(2)
- 2x 24" Uprights
- 2x 80" Crossbeams with Strap Assist and End Caps
- 2x Mounting Bracket - 2" Channel w/ 1/2" Hexagonal Holes
- 4x Zinc Bolt and Nut to Tighten Crossbeam to Mounting Bracket
- 4x Zinc U Bolts with Washer and Nut for Adjusting and Securing Crossbeams
- 4x Galvanized U Bolts with Washer and Nut for Securing Uprights to 1.5" & 2" Tubing
- 4x Galvanized U Bolts with Washer and nut for Securing Uprights to 3" wide Tubing
- 4x Turned Eye Bolts for Securing Tie Downs
- 8x Galvanized Lock Nuts for Securing Eye Bolts
Click the following link for Assembly Instructions
https://cdn.shopify.com/s/files/1/1557/3371/files/Canoe_Kayak_Kit_Assembly_Instructions.pdf
2 x 4 x 10′ Black Marine Carpeted Bunk Board
$59.99 $55.00
Brand Com-Fab
General
2 x 4 x 10′ Black Marine Carpeted Bunk Board
This item is not shipped! Pickup only from our location at 2375 Pleasantdale Rd. Atlanta, GA 30340
These are used as the standard option for JBT-1600 'River Hawk' Trailer models, as well as an upgradeable option for the JBT-1400 model.
'River Hawk' Jon Boat Trailer Bunk Mounting Kit
MODEL: CFBUNKBRDC-10FT
Used on
2 x 4 x 16′ Black Marine Carpeted Bunk Board
$69.99 $65.00
Brand Com-Fab
General
2 x 4 x 16′ Black Marine Carpeted Bunk Board
This item is not shipped! Pickup only from our location at 2375 Pleasantdale Rd. Atlanta, GA 30340
These are used for PT-1618, and PT-1820 trailer models.
MODEL: CFBUNKBRDC-16FT
Used on
2 x 4 x 2′ Black Marine Carpeted Bow Support Bunk
$12.50
Brand Com-Fab
General
2 x 4 x 2′ Black Marine Carpeted Bow Support Bunk
This item is mounted with a Jon Boat Trailer Bow Support Bunk Mounting Kit to all Jon Boat Trailer models except the JBT-1600 'River Hawk'.
MODEL: CFBOWSPRTC-2FT
Used on
2 x 4 x 5′ Black Marine Carpeted Bunk Board
$29.99 $25.00
Brand Com-Fab
General
2 x 4 x 5′ Black Marine Carpeted Bunk Board
These are used for PWT-800, and PWT-2212 trailer models.
Single PWC Zinc Bunk Mounting Kit
Single PWC Galvanized Bunk Mounting Kit
MODEL: CFBUNKBRDC-5FT
Used on
2 x 4 x 6′ Black Marine Carpeted Bunk Board
$34.99 $30.00
Brand Com-Fab
General
2 x 4 x 6′ Carpeted Black Marine Bunk Board
These are used on PWT-1000, PWT-1100, PWT-2213, PWT-2214, and all Jon Boat Trailer models.
Jon Boat Trailer Bunk Mounting Kit
MODEL: CFBUNKBRDC-6FT
Used on
2-Leaf Slipper Springs w/ Radius 550 lb Capacity (Qty 2)
$55.00
Brand Com-Fab
General
2-Leaf Slipper Springs w/ Radius 550 lb Maximum Capacity (Qty 2)
This item is mounted to the 1000 lb Galvanized Trailer Axle, and the 1000 lb Black Powder Coated Trailer Axle using a Zinc Tie Plate Kit.
TIE DOWN MODEL: #13070
MODEL: CFAXLE2-LSPRNG(SL)
Specifications
Length: 24.63"
Leaf Width: 1.75"
Arch Height: 4.50"
Bushing Type: Nylon
Used on
2000 lb Extended Galvanized PWC Trailer Axle w/ 545 Hubs and Springs HF 91.5 SC 81.5
$349.99
Brand Com-Fab
General
2000 lb Extended Galvanized PWC Trailer Axle w/ 545 Hubs and Springs
This item is not shipped. Pickup only from our location at 2375 Pleasantdale Rd. Atlanta, GA 30340.
*NOTE: if your trailer is older than 2006, call before ordering to ensure you receive the correct axle.*
Materials Include:
1 - 84.45" x 1.5" x 1.5" x 11 Gauge Galvanized Axle Tubing
2 - Galvanized 5-Bolt Hub Assembly
2 - 3-Leaf Slipper Springs (750 lb)
This item is mounted to the PWT-2212G trailer model with a Galvanized Axle Mounting Kit, and to the PWT-2212B trailer model with a Black Powder Coated Axle Mounting Kit
MODEL: CFAXLE2000G-EXTENDED
Specifications
Tubing: 1.5" Galvanized Square Axle
Load Rating: 2000 lb
Hub Face: 91.5"
Spring Center: 81.5"
Overall Length: 56"
Bearing Size: 1-1/16"
Used on
20′ Winch Strap w/ 1" Hook (4000 lb Max Capacity) - Dutton-Lainson
$27.50
Brand Com-Fab
General
20′ Winch Strap w/ Hook (4000 lb Max Capacity)
- Dutton-Lainson black heavy duty winch strap and hook
- For winches up to 2,600 lb. capacity
- 2" wide x 20' long
- 4,000 lb. breaking strength
- Snap Hook has a tensile strength of 7,500 lbs.
- Includes a 3/8" x 3" bolt, a 3/8" x 3-1/4" bolt, and a 3/8" locknut to install strap onto winch drum
MODEL: CFWNCHSTRAP-20FT(4K-DL)
Used on
PT-161821' 4-Pin Wire Harness Assembled w/ Protective Sleeve
$18.00
Brand Com-Fab
General
21' 4-Pin Wire Harness Assembled w/ Protective Sleeve
The wiring is pulled through the trailer frame to provide connection between the lighting and the vehicle. It connects to the vehicle with a 4-Pin Male Connector. This item comes with a 3/8 20" Protective Sleeve and 30" Ground with 1/2" ring terminal.
MODEL: CFWH21
Used on
JBT-1600 ‘RIVER HAWK’
2212B - Bunk Mounting Kit
$24.99
Brand Com-Fab
General
2212B - Bunk Mounting Kit
These are all of the requisite materials needed to mount a 2″ x 4″ x 5′ Black Marine Carpeted Bunk Board onto a 2212B trailer model.
Materials Include:
2 – 5"x 1.25" x .25" Zinc Flat Plate
2 – Galvanized Angular Swivel Bracket
4 – 5/16" x 1-1/2″ Galvanized Hex Head Lag Screw
MODEL: CFBNKKIT-2212B
Used on
PWT-2212B
2212B - Fender Mounting Kit
$14.99
Brand Com-Fab
General
2212B - Fender Mounting Kit
These are all of the requisite materials to mount a Black Powder Coated Fender 4.80 x 12" Tire onto a 2212B trailer model.
Materials Include:
4 – 3/8″ Zinc Hex Flange Top Lock Nut
MODEL: CFFNDRKIT-2212B
Used on
PWT-2212B
2212G - Fender Mounting Kit
$15.99
Brand Com-Fab
General
2212G - Fender Mounting Kit
These are all of the requisite materials needed to mount a Galvanized Fender 4.80 x 12” Tire onto a 2212G trailer model.
Materials Include:
4 – 3/8" Galvanized Tri-Lock Nut
MODEL: CFFNDRKIT-2212G
Used on
PWT-2212G