PWT-2212B Parts
Dry Launch SP7 Red Tail Light (Passenger Side) - Incandescent
$20.00
Brand Com-Fab
General
Dry Launch SP7 Red Tail Light (Passenger Side) - Incandescent
The Dry Launch submersible 7-function passenger side tail light is waterproof with a bulb slide that has built-in dust, and splash guard. It snaps out for easy bulb replacement.
Dimensions: W = 6" H = 3.5" D = 2-1/4"
Materials Include:
2 - 1/4"-18 Zinc Nut
MODEL: CFLIGHTREAR(R)-INC(DL)
Optional for
ALL COM-FAB TRAILER MODELS
Locking Spare Tire Bracket, Fits 3″ Width Tubing
$19.99
Brand Com-Fab
General
Locking Spare Tire Bracket, fits 3″ Width Tubing
This item is used to lock down, and transport a spare tire on all Com-Fab trailer models. Lock not included.
MODEL: CFSTB-TOP
Optional for
ALL COM-FAB TRAILER MODELS
Dry Launch SP7 Red Tail Light (Driver Side) - Incandescent
$20.00
Brand Com-Fab
General
Dry Launch SP7 Red Tail Light (Driver Side) - Incandescent
The Dry Launch submersible 8-function driver side tail light is waterproof with a bulb slide that has a built-in dust and splash guard. It snaps out for easy bulb replacement.
Dimensions: W = 6" H = 3.5" D = 2-1/4"
Materials Include:
MODEL: CFLIGHTREAR(L)-INC(DL)
Optional for
ALL COM-FAB TRAILER MODELS
TecNiq-T86 7 Function 6" LED Tail Light (Passenger Side)
$34.99 $24.00
Brand Com-Fab
General
TecNiq-T86 7 Function 6" Box LED Passenger Side Tail Light w/ Pigtail
- These are optional for all Trailer Models.
- Multi-Function 6" Box Tail Light
- Urethane Potting w/ Guaranteed Circuit Board Protection
- Dust and water proof with hermetic seal
- Durable impact resistant lens
- Meets all FMVSS 108 requirements for narrow and wide vehicles
- Reliable performance over 100,000 hours
- Fits standard mounting as a direct replacement
- Functions include: Stop, Turn, Tail, Clearance, Side marker, Side Reflector,
Rear Reflector, and License Plate Light (Left)
Includes two 7/16" bolts w/ nuts for mounting.
MODEL: CFLIGHTREAR(R)-LED(TEC)
Used on
ALL COM-FAB TRAILER MODELS
Black Powder Coated 545 Bolt 1250/1350LB Hub Assembly - Dexter
$79.99 $69.99
Brand Com-Fab
General
Black Powder Coated 545 Bolt 1250/1350LB Hub Assembly w/ Bearings, Seal, Amp, and Dust Cap - Dexter
Hub Includes:
- Triple Lip Grease Seal - 1.25" I.D. - 1.98"
- 1-1/16" Bearing Cup
- Cotter Pin
MODEL: CFAXLE-HUB5BLT(1350-B)
Used on
TecNiq-T86 8 Function 6" LED Tail Light (Driver Side)
$34.99 $25.75
Brand Com-Fab
General
TecNiq-T86 8 Function 8" Box Driver Side Tail Light w/ Pig Tail.
-
Multi-Function 6" box tail light
-
Urethane Potting w/ Guaranteed Circuit Board Protection
-
Dust and water proof with hermetic seal
-
Durable impact resistant lens
-
Meets all FMVSS 108 requirements for narrow and wide vehicles
-
Reliable performance over 100,000 hours
-
Fits standard mounting as a direct replacement
-
Functions include: Stop, Turn, Tail, Clearance, Side marker, Side Reflector,
Rear Reflector, and License Plate Light (Left)
Includes two 7/16" bolts w/ nuts for mounting.
MODEL: CFLIGHTREAR(L)-LED(TEC)
Used on
ALL COM-FAB TRAILER MODELS
2″ Steel Super Lube Grease Dust Cap & Plug Set (2x)
$9.99
Brand Com-Fab
General
2″ Steel Super Lube Grease Dust Cap & Plug for Axle Hub
This item is a part of all hub assemblies and comes as a pair.
Galvanized 5-Bolt Hub Assembly
Powder Coated Black 5-Bolt Hub Assembly
TIE DOWN MODEL: #17093
MODEL: CFAXLE-CAP&PLUG
Used on
ALL COM-FAB TRAILER MODELS
License Plate Bracket by TecNiq, black
$9.99 $2.00
Brand Com-Fab
General
TecNiq License Plate Bracket
TECNIQ MODEL: L95-0B00-1
MODEL: CFTAG-TEC
Used on
ALL COM-FAB TRAILER MODELS
1200 lb Side Crank Swivel Jack
$49.99
Brand Com-Fab
General
1200 lb Side Crank Swivel Jack
This item fits 3″ x 5“ tongues. It comes with a 1200 lb Side Crank Swivel Jack Mounting Kit.
MAXIMUM CAPACITY: 1200LB
PACIDIC RIM MODEL: MJ-1200B
MODEL: CFJACKSIDE
Used on
JBT-900
JBT-1400
JBT-1600
JBT-1600 ‘RIVER HAWK’
PT-1400 'MiniToon'
PT-1618
PT-1820
PT-2022
21' 4-Pin Wire Harness Assembled w/ Protective Sleeve
$18.00
Brand Com-Fab
General
21' 4-Pin Wire Harness Assembled w/ Protective Sleeve
The wiring is pulled through the trailer frame to provide connection between the lighting and the vehicle. It connects to the vehicle with a 4-Pin Male Connector. This item comes with a 3/8 20" Protective Sleeve and 30" Ground with 1/2" ring terminal.
MODEL: CFWH21
Used on
JBT-1600 ‘RIVER HAWK’
RAM 2″ Coupler fits 3″ Wide Tongue
$27.99
Brand Com-Fab
General
RAM 2″ (Class 2) Zinc Plated Coupler fits 3″ Wide Tongue
This item is mounted to PWT-800, PWT-1000, PWT-1100, PWT-2212, and all Jon Boat Trailer models with a Coupler Mounting Kit
MODEL: CFCPLR(RAM)-3x2
Specifications
- Hole Diameter: 1/2"
- Hole Distance: 2 1/2"
- Hole Distance from Top: 7/8"
- Hole Distance from Base: 1"
Used on
RAM 600 lb Capacity Crank Winch with Strap and Hook
$32.00
Brand Com-Fab
General
RAM 600 lb Capacity Crank Winch w/ Mounting Kit
This item is a light duty winch with permanently lubricated bearings used for horizontal pulling applications. The item has a 12′ Winch Strap w/ Spring Loaded Hook and Loop End, and a RAM 600 lb Winch Handle. The mounting materials are sold separately.
Mounting Kit Includes:
2 - 3/8"-16 x 1" Zinc Hex Head Cap Bolt
2 - 3/8"-16 Serrated Zinc Flange Nuts
MODEL: CFWNCH600TT
Used on
Dry Launch 60″ Red Triple Light Bar
$11.25
Brand Com-Fab
General
Dry Launch 60″ Red Triple Light Bar
This light bar can be mounted to all Double PWT, and Pontoon Boat Trailer models. It is secured with two 12 x 3/4″ Zinc Hex Washer Head Tek #3 Screws.
MODEL: CFLIGHTBAR-60
Optional for
4.80 x 12″ C Load Range Silver E-Coat Tire & Wheel, Bias - Kenda/Loadstar
$69.99 $65.99
Brand Com-Fab
General
4.80 x 12″ C Load Range Silver E-Coat Finish Tire & Wheel, Bias - Kenda/Loadstar
This is the tire and wheel used on PWT-800B, PWT-1000B, PWT-1100B, and PWT-2212B black powder coated trailer models. Tire capacity is 990lbs (450kg). Speed rating 65 mph.
MODEL: CFT48012S-LRC
Used on
2000 lb Extended Galvanized PWC Trailer Axle w/ 545 Hubs and Springs HF 91.5 SC 81.5
$349.99
Brand Com-Fab
General
2000 lb Extended Galvanized PWC Trailer Axle w/ 545 Hubs and Springs
This item is not shipped. Pickup only from our location at 2375 Pleasantdale Rd. Atlanta, GA 30340.
*NOTE: if your trailer is older than 2006, call before ordering to ensure you receive the correct axle.*
Materials Include:
1 - 84.45" x 1.5" x 1.5" x 11 Gauge Galvanized Axle Tubing
2 - Galvanized 5-Bolt Hub Assembly
2 - 3-Leaf Slipper Springs (750 lb)
This item is mounted to the PWT-2212G trailer model with a Galvanized Axle Mounting Kit, and to the PWT-2212B trailer model with a Black Powder Coated Axle Mounting Kit
MODEL: CFAXLE2000G-EXTENDED
Specifications
Tubing: 1.5" Galvanized Square Axle
Load Rating: 2000 lb
Hub Face: 91.5"
Spring Center: 81.5"
Overall Length: 56"
Bearing Size: 1-1/16"
Used on
3-Leaf Slipper Flat Springs 750 lb Capacity (Qty 2)
$89.99
Brand Com-Fab
General
3-Leaf Slipper Springs 750 lb Maximum Capacity (Qty 2)
- This item is mounted to the 1500 lb Galvanized Trailer Axle, as well as the 1500 lb Extended Galvanized Trailer Axle with a Galvanized Tie Plate Kit.
- This item is mounted to the 1500 lb Black Powder Coated Trailer Axle with a Zinc Tie Plate Kit.
TIE DOWN MODEL: #13087
MODEL: CFAXLE-LSPRNG(3-SF)
Specifications
Length: 24.63"
Leaf Width: 1.75"
Arch Height: 4.50"
Bushing Type: Nylon
Used on
Winch Poly Bow Roller Assembly
$29.99
Brand Com-Fab
General
Winch Poly Bow Roller Assembly
This kit is part of every Winch Assembly used on every PWT, and Jon Boat Trailer model.
Materials Include:
1 – Galvanized Bow Stop Bracket
1 – 3/8″-16 x 3.75″ Zinc Hex Head Cap Bolt
1 – 3/8″-16 Zinc Hex Flange Top Lock Nut
1 – 1/2″-13 x 4.5″ Zinc Hex Head Cap Bolt
2 – 3″ Amber Poly Bow Roller Bell End
MODEL: CFASSM-WNCHRLR(3)
Used on
Galvanized Tie Plate Kit for 1.5" Square Trailer Axle
$34.99
Brand Com-Fab
General
Galvanized Tie Plate Kit for 1.5" Square Trailer Axles
This kit is used to mount springs to Galvanized 1.5" Square Trailer Axles. The kit is a part of the 1500 lb Galvanized Trailer Axle used on every PWT-1000G, and PWT-1100G trailer model. It is also part of the 1500 lb Extended Galvanized Trailer Axle used on both PWT-2212 trailer models.
Materials Include:
2 - Galvanized Axle Tie Plate for 1.5" Square Trailer Axle
4 - 3/8"-16 x 1.56" x 3.63" Galvanized U-Bolt
8 - 3/8"-16 Galvanized Tri-Lock Nut
8 - 3/8" Galvanized Lock Washer
MODEL: CFAXLEKIT-SPRNGMNT(1.5K-G)
Used on
3/8"-16 Zinc Hex Flange Top Lock Nut
$0.75
Brand Com-Fab
General
3/8"-16 Zinc Hex Flange Top Lock Nut Zinc
This item is part of the:
– 1000B - Bunk Mounting Kit
– 2212B - Fender Mounting Kit
– 2213B - Fender Mounting Kit
– Winch Poly Bow Roller Assembly
– Pontoon Boat Trailer Winch Assembly
MODEL: CFNUT3/8LOCKZ
Used on
ALL COM-FAB TRAILER MODELS
Galvanized Angular Swivel Bracket - 7/16″ Top Hole
$4.99
Brand Com-Fab
General
Galvanized Angular Swivel Bracket - 7/16″ Top Hole
These are used to mount bunk boards onto all Jon Boat, and PWT Trailer models.
This item is part of these kits:
- Jon Boat Trailer Bunk Mounting Kit
- Jon Boat Trailer Bow Support Mounting Kit
- 'River Hawk' Jon Boat Trailer Bunk Mounting Kit
MODEL: CFBRKTSWIVEL
Used on
5/16″ x 1-1/2″ Galvanized Hex Head Lag Screw
$0.70
Brand Com-Fab
General
5/16″ x 1-1/2″ Galvanized Hex Head Lag Screw
It is used for mounting Bunk Boards to Galvanized Angular Swivel Brackets, and Pontoon Boat Trailer Bunk Brackets on all trailer models.
MODEL: CFSCRWLAG-5/16-0150
Used on
ALL COM-FAB TRAILER MODELS
Galvanized Bow Stop Bracket
$11.99
Brand Com-Fab
General
Galvanized Bow Stop Bracket
This item is part of the Winch Poly Bow Roller Assembly used on every type of winch stand for all Jon Boat, and PWT trailer models.
MODEL: CFBRKTWNCHRLR
Used on
1"-14 Thread 12 Position Castle Nut
$4.00
Brand Com-Fab
This product is sold out
General
12 Position Castle Nut
This item is fastened to the end of an Axle Spindle with the use of a 5/32" x 2" Zinc Plated Cotter Pin. This combination secures Hubs to all PWC Trailer Models. It is rated for axles less than 3000 lbs. It is a 1"-14 Thread 12-Slot Castle Nut to fit standard 1" trailer spindles.
TIE DOWN MODEL: #10634
MODEL: CFAXLE-NUT(CASTLE-L)
Used on
1-1/16" L44649 Bearings
$5.75
Brand Com-Fab
General
1-1/16" L44649 Bearings
These bearings fit a 1-1/16" diameter Spindle Shaft, and are used with L44610 Bearing Cups. These are used on Tie-Down #1350, and #1750 Hubs
UNIVERSAL MODEL: L44649
TIE DOWN MODEL: #11054
MODEL: CFAXLE-BRG(1-1/16")-INNER/OUTER
Used on
ALL COM-FAB PWC, JON BOAT, AND CANOE/KAYAK TRAILER MODELS