PWT-2214G Parts
1"-14 Thread 12 Position Castle Nut
$4.00
Brand Com-Fab
This product is sold out
General
12 Position Castle Nut
This item is fastened to the end of an Axle Spindle with the use of a 5/32" x 2" Zinc Plated Cotter Pin. This combination secures Hubs to all PWC Trailer Models. It is rated for axles less than 3000 lbs. It is a 1"-14 Thread 12-Slot Castle Nut to fit standard 1" trailer spindles.
TIE DOWN MODEL: #10634
MODEL: CFAXLE-NUT(CASTLE-L)
Used on
1-1/16" L44649 Bearings
$5.75
Brand Com-Fab
General
1-1/16" L44649 Bearings
These bearings fit a 1-1/16" diameter Spindle Shaft, and are used with L44610 Bearing Cups. These are used on Tie-Down #1350, and #1750 Hubs
UNIVERSAL MODEL: L44649
TIE DOWN MODEL: #11054
MODEL: CFAXLE-BRG(1-1/16")-INNER/OUTER
Used on
ALL COM-FAB PWC, JON BOAT, AND CANOE/KAYAK TRAILER MODELS
Side Crank Swivel Jack Mounting Kit for 1200/1500lb Jacks
$14.99
Brand Com-Fab
General
Side Crank Swivel Jack Mounting Kit
This kit contains all of the parts needed to mount the 1200 lb Side Crank Swivel Jack, as well as the 1500 lb Side Crank Swivel Jack to all trailer frame models
MODEL: CFJACK-MNTKIT
Used on
ALL COM-FAB TRAILER MODELS
2213/4G - Fender Mounting Kit
$19.99
Brand Com-Fab
General
2213/4G - Fender Mounting Kit
This kit contains all of the requisite materials needed to mount a Galvanized Fender 13" Tire onto 2213G, 2214G, and Pre-2019 Single Axle Pontoon Boat Trailer models.
Materials Include:
2 – 3/8″-16 x 4.19″ x 3″ Galvanized U-Bolt
2 – 6" x 1.5" x 1.25" Galvanized Flat Plate
4 – 3/8″ Galvanized Tri-Lock Hex Nuts
MODEL: CFFNDRKITG-2213
Used on
21' 4-Pin Wire Harness Assembled w/ Protective Sleeve
$26.25
Brand Com-Fab
General
21' 4-Pin Wire Harness Assembled w/ Protective Sleeve
The wiring is pulled through the trailer frame to provide connection between the lighting and the vehicle. It connects to the vehicle with a 4-Pin Male Connector. This item comes with a 3/8 20" Protective Sleeve and 30" Ground with 1/2" ring terminal.
MODEL: CFWH21
Used on
JBT-1600 ‘RIVER HAWK’
1/2″-20 Lug Nut (Set of 5)
$7.50
Brand Com-Fab
General
1/2″-20 Lug Nut (Set of 5)
These are used for mounting tires on all trailer models to 1 1/2"-20 Threaded Stud.
MODEL: CFNUTLUG
Used on
ALL COM-FAB TRAILER MODELS WITH SILVER E-COAT OR GALVANIZED WHEELS
1/4″-20 Thread Carriage 307A Bolt, Zinc
$0.15
Brand Com-Fab
General
- Two of these are used with 1/4″ Zinc Nuts to mount TecNiq 8 Function 6" LED Tail Lights & TecNiq 7 Function 6" LED Tail Lights to all current Com-Fab Trailer Models
- Two of these are used with 1/4″ Zinc Nuts to mount Dry Launch Submersible Tail Lights to Pre-2018 Com-Fab trailer models.
MODEL: CFBLTLIGHT
Used On
ALL COM-FAB TRAILER MODELS
8.25" x 1.5" x .25" Galvanized Flat Plate w/ 7/16" Holes - Shackle Link
$6.99
Brand Com-Fab
This product is sold out
General
8.25" x 1.5" x .25" Galvanized Flat Plate w/ 7/16" Holes and 3.5" Hole Centers - Shackle Link
This item is part of the 2213G - Bunk Board Mounting Kit used to mount Bunk Boards onto PWT-2213G, and PWT-2214G trailer models.
MODEL: CFFLTSTRPBUNK(DBL)G
Used on
3/8″-16 x 3.06" x 4.5″ Galvanized U-Bolt
$3.99
Brand Com-Fab
General
3/8″-16 x 3.06" x 4.5″ Galvanized U-Bolt
This item is part of these kits:
- Galvanized Winch Assembly Mounting Kit
- Jon Boat Trailer Bow Support Bunk Mounting Kit
MODEL: CFUBLT3/8X4.5G
Used on
2500 lb Galvanized PWC Trailer Axle w/ 545 Hubs and Springs HF 93.5 SC 83.5
$490.00
Brand Com-Fab
General
2500 lb Galvanized PWC Trailer Axle w/ 545 Hubs and Springs
*This item is not shipped! Pickup only from our location at 2375 Pleasantdale Rd. Atlanta, GA 30340*
*NOTE: if your trailer is older than 2006, call before ordering to ensure you receive the correct axle.*
Materials Include:
1 - 83" x 2" x 2" x 3/16" Gauge Galvanized Axle Tubing
2 - Galvanized 5-Bolt Hub Assembly
2 - 5-Leaf Slipper Springs (1,250 lb)
This item is mounted to the PWT-2213G, and PWT-2214G trailer models with a Galvanized Axle Mounting Kit.
MODEL: CFAXLE2500G
Specifications
Tubing: 2" Galvanized Square Axle
Load Rating: 2500 lb
Hub Face: 93.5"
Spring Center: 83"
Overall Length: 98.5
Bearing Size: 1-1/16"
Used on
Rhino Kote Galvanizing Graphic (4.5" x 3.5")
$3.99
Brand Com-Fab
General
Rhino Kote Galvanizing Graphic (4.5" x 3.5")
Dimensions: 4.5" x 3.5"
MODEL: CFGRAPHIC-RHINOKOTE (4X3)
Used on
Company Graphic for Double PWT and Pontoon Trailers
$14.99
Brand Com-Fab
General
Company Graphic for Double PWT and Pontoon Trailers
This graphic sticks to the side of all Double PWT and Pontoon Boat Trailer models.
Dimensions: 30.25" x 3"
MODEL: CFGRAPHIC-(4X2)
Used on
Coupler Mounting Kit for 3" Wide Trailer Tongues
$7.99
Brand Com-Fab
General
Coupler Mounting Kit for 3" Wide Trailer Tongues
This item is used to mount Couplers to all trailer models without Brakes.
Materials Include:
2 - 1/2″-13 x 4″ Zinc Hex Head Cap Bolt
2 - 1/2″- 13 Zinc Top Lock Nut
MODEL: CFCPLR-MNTKIT(NONBRK)
Used on
ALL COM-FAB TRAILER MODELS
Galvanized Winch Assembly Mounting Kit
$14.99
Brand Com-Fab
General
Galvanized Winch Assembly Mounting Kit
This kit contains all of the requisite materials needed to mount a Galvanized Winch Assembly onto all Galvanized PWT trailer models.
Materials Include:
2 – 3/8″ x 3.06" x 4.5″ Galvanized U-Bolt
2 – 5" x 1.25" x .25" Galvanized Flat Plate
4 – 3/8″ Galvanized USS Flat Washer
4 – 3/8″-16 Galvanized Tri-Lock Hex Nuts
MODEL: CFWNCHKITG
Used on
3" Poly Bow Roller Assembly
$19.99
Brand Com-Fab
General
3" Poly Bow Roller Assembly
This is a section of the Winch Poly Bow Roller Assembly.
Materials Include:
1 – 3″ Poly Bow Roller
2 – 3″ Poly Bow Roller Bell End
1 – 1/2″-13 x 4.5″ Zinc Bolt
2 – 1/2″ Zinc Flat Washer
1 – 1/2″-13 Top Lock Nut
MODEL: CFASSM-POLYRLR(3)
Used on
10.25" Black Marine Carpet
$2.50
Brand Com-Fab
General
Black Marine Carpet 10.25" Width
$2/ft in 100 ft rolls
- This carpet is used for bunks on all of our PWC Trailer, and Jon Boat Trailer models. It is optional for our Pontoon Trailer models and Canoe/Kayak Angler Kits.
If you are purchasing this carpet it needs to be a foot longer than the board itself.
This carpet comes in these specific sizes as well:
- 5 ft Bunk Board Black Marine Carpet
- 6 ft Bunk Board Black Marine Carpet
- 7 ft Bunk Board Black Marine Carpet
MODEL: CFBNKCOVER-CARPET(10.25)
Used on
JBT-900
JBT-1400
JBT-1600
JBT-1600 ‘RIVER HAWK’
Optional for
1/4″-20 Thread External Tooth Locknut, Zinc - For Tail Lights
$0.15
Brand Com-Fab
General
1/4″-20 Thread External Tooth Locknut, Zinc Nut for Tail Lights
- Two of these are used with 1/4″- 20 Tail Light Bolts to mount TecNiq 8 Function 6" LED Tail Lights to all current Com-Fab Trailer models.
- Two of these are used with 1/4″- 20 Tail Light Bolts to mount Dry Launch SP7 Red Tail Lights to all Pre-2018 Com-Fab trailer models.
- One of these is used w/ 2-3/4"-20 Thread Bolts to secure PWT winch strap to crank winch.
MODEL: CFNUT1/4LOCKZ
Used on
ALL COM-FAB TRAILER MODELS
3/8″-16 Serrated Zinc Flange Nut
$0.15
Brand Com-Fab
General
3/8″-16 Serrated Zinc Flange Nut
This item is part of these kits:
- 3/8"-16 Zinc Hex Head Bolts to mount all Crank Winch Models onto all Winch Post models.
- Black Powder Coated Winch Assembly Mounting Kit
- Jon Boat Trailer Winch Assembly Mounting Kit
MODEL: CFNUT3/8SERTDZ
Used on
ALL Powder Coat Finish Trailer Models, and Most Galvanized Trailer Models for Winches
6" x 1.5" x .25" Galvanized Flat Plate w/ 7/16" Holes - Shackle Link
$4.99
Brand Com-Fab
General
6" x 1.5" x .25" Galvanized Flat Plate w/ 2 7/16" Holes and 4.5" Hole Centers - Shackle Link
- This item is part of the 2213G - Fender Mounting Kit used to mount Fenders to PWT-2213G, and PWT-2214G Trailer models.
MODEL: CFFLTSTRPFNDR(DBL)G
Used on
3/8″-16 x 1″ Zinc Hex Head Cap Bolt
$1.25
Brand Com-Fab
General
3/8″-16 x 1″ Zinc Hex Head Cap Bolt
This item is used with 3/8"-16 Serrated Zinc Flange Nuts to mount all crank winch models onto every type of winch post. It is also part of the 2213B - Bunk Mounting Kit used to mount bunks onto PWT-2213B, and PWT-2214B trailer models.
MODEL: CFBLT3/8X1Z
Used on
ALL COM-FAB TRAILER MODELS
2″ x 4″ x 7′ Black Marine Carpeted Bunk Board
$35.00
Brand Com-Fab
General
2″ x 4″ x 7′ Black Marine Carpeted Bunk Board
These are used for all PWT-1100, and PWT-2214 trailer models.
MODEL: CFBUNKBRDC-7FT
Used on
32″ Galvanized Winch Post
$75.00
Brand Com-Fab
General
32″ Galvanized Winch Post
- This item is part of the 32″ Galvanized Winch Assembly which is mounted to the PWT-2213G, and PWT-2214G trailer models.
- This item is part of the 32" Galvanized Jon Boat Trailer Winch Assembly which is mounted every Jon Boat Trailer model.
MODEL: CFWNCHPOST(PWC-32)-G
Used on
Dutton-Lainson 600 lb Winch Handle
$16.99
Brand Com-Fab
General
Dutton-Lainson 600 lb Winch Handle
This ergonomic handle attaches to a Dutton-Lainson 600 lb Capacity Crank Winch with 1/2" Nylock Nut.
DUTTON-LAINSON MODEL: #70304
MODEL: CFWNCHHANDLE-DL600
Used on
3″ Amber Poly Bow Roller Bell End
$5.80
Brand Com-Fab
General
3″ Amber Poly Bow Roller Bell End
This item is used as part of every Winch Assembly mounted on every PWT, and Jon Boat Trailer model.
This item is part of these assemblies:
- Winch Poly Bow Roller Assembly
TIE DOWN MODEL: #48654
MODEL: CFPOLYEBELL-3