PWT-2212G Parts

General

Dry Launch SP7 Red Tail Light (Passenger Side) - Incandescent

The Dry Launch submersible 7-function passenger side tail light is waterproof with a bulb slide that has built-in dust, and splash guard. It snaps out for easy bulb replacement.

Dimensions:  W = 6"   H = 3.5"   D = 2-1/4"

Materials Include:

2 - 1/4″-18 Tail Light Bolt

2 - 1/4"-18 Zinc Nut

MODEL: CFLIGHTREAR(R)-INC(DL)

MPN: SP7RBX-99X1

Optional for

ALL COM-FAB TRAILER MODELS

General

Locking Spare Tire Bracket, fits 3″ Width Tubing

This item is used to lock down, and transport a spare tire on all Com-Fab trailer models. Lock not included.

MODEL: CFSTB-TOP

Optional for

ALL COM-FAB TRAILER MODELS

General

TecNiq-T86 7 Function 6" Box LED Passenger Side Tail Light w/ Pigtail

• These are optional for all Trailer Models.
• Multi-Function 6" Box Tail Light
• Urethane Potting w/ Guaranteed Circuit Board Protection
• Dust and water proof with hermetic seal
• Durable impact resistant lens
• Meets all FMVSS 108 requirements for narrow and wide vehicles
• Reliable performance over 100,000 hours
• Fits standard mounting as a direct replacement
• Functions include: Stop, Turn, Tail, Clearance, Side marker, Side Reflector,
  Rear Reflector, and License Plate Light (Left)

Includes two 1/4-20 Thread bolts w/ nuts for mounting.

MODEL: CFLIGHTREAR(R)-LED(TEC)

MPN: T86-RR2RG-1

Used on

ALL COM-FAB TRAILER MODELS

General

TecNiq-T86-L 8 Function 8" Box Driver Side Tail Light w/ Pig Tail.

• Multi-Function 6" box tail light
• Urethane Potting w/ Guaranteed Circuit Board Protection
• Dust and water proof with hermetic seal
• Durable impact resistant lens
• Meets all FMVSS 108 requirements for narrow and wide vehicles
• Reliable performance over 100,000 hours
• Fits standard mounting as a direct replacement
• Functions include: Stop, Turn, Tail, Clearance, Side marker, Side Reflector,
  Rear Reflector, and License Plate Light (Left)

Includes two 1/4-20 Thread bolts w/ nuts for mounting.

MODEL: CFLIGHTREAR(L)-LED(TEC)

MPN: T86-RR2LG-1

Used on

ALL COM-FAB TRAILER MODELS

General

Complete 545 Bolt 1250/1350LB Hub Assembly w/Bearings, Seal, Amp and Dust Cap - Dexter

Hub Includes:

- Triple Lip Grease Seal - 1.25" I.D. - 1.98"

- 1-1/16" Bearing Cup

- 1-1/16" L44649 Bearings

- 1-1/2"-20 Lug Nut Studs

- 1/2″-20 Lug Nut (Set of 5)

- 1.98" Dust Cap

- Super Lube Rubber Grommet

-Cotter Pin

TIEDOWN MODEL: #46205X

MODEL: CFAXLEKIT-HUB5BLT(1350-Z)

*Note: As of Summer 2026, this Product has been replaced with a Zinc-Plated Finish. Dexter Axle has discontinued production of GalvX hubs.

Used on

General

2″ Steel Super Lube Grease Dust Cap & Plug for Axle Hub

This item is a part of all hub assemblies (outside of Vortex Axle Hubs) and comes as a pair.

Galvanized 5-Bolt Hub Assembly

Powder Coated Black 5-Bolt Hub Assembly

DEXTER MODEL: #021-041-01 (Dome Cap), #085-001-00 (Plug)

MODEL: CFAXLE-CAP&PLUG-(Q2)

Used on

ALL COM-FAB TRAILER MODELS

General

TecNiq License Plate Bracket

MODEL: CFTAG-TEC

TECNIQ MODEL: L95-0B00-1

Used on

ALL COM-FAB TRAILER MODELS

General

Dry Launch SP7 Red Tail Light (Driver Side) - Incandescent

The Dry Launch submersible 8-function driver side tail light is waterproof with a bulb slide that has a built-in dust and splash guard. It snaps out for easy bulb replacement.

Dimensions:  W = 6"   H = 3.5"   D = 2-1/4"

Materials Include:

2 - 1/4″ - 18 Tail Light Bolt

2 - 1/4" -18 Zinc Nut

MODEL: CFLIGHTREAR(L)-INC(DL)

MPN: SP7RBX-99X1

Optional for

ALL COM-FAB TRAILER MODELS

General

4.80 x 12″ C Load Range 545 Hole Pattern Galvanized Finish Bias Tire & Wheel - Kenda/Loadstar

Tire Characteristics:

MODEL: CFT48012G-LRC

Used on:

General

RAM 1200LB Side Crank Swivel Jack

This item fits 3″ x 3" - 5“ tongues. Mounting Hardware is included.

MAXIMUM CAPACITY: 1200LB

RAM MODEL: MJ-1200B

MODEL: CFJACKSIDE-1200(RAM)

Used on

PWT-2214G 
JBT-1200 (Formerly JBT-900)
JBT-1400 
JBT-1600
JBT-1600 (EXT) ((Formerly JBT-1600 ‘RIVER HAWK’)
PT-1400 'MiniToon'
PT-/TT-1618
PT-/TT-1820
PT-/TT-2022

General

RAM 600 lb Capacity Crank Winch w/ Mounting Kit

This item is a light duty winch with permanently lubricated bearings used for horizontal pulling applications. The item has a 12′ Winch Strap w/ Spring Loaded Hook and Loop End, and a RAM 600 lb Winch Handle. The mounting materials are sold separately.

Mounting Kit Includes:

2 - 3/8"-16 x 1" Zinc Hex Head Cap Bolt

2 - 3/8"-16 Serrated Zinc Flange Nuts

MODEL: CFWNCH600(RAM)

MPN: HWSP-600

Used on

General

3-Leaf Slipper Springs 750 lb Maximum Capacity (Qty 2)

- This item is mounted to the 1500 lb Galvanized Trailer Axle, as well as the 1500 lb Extended Galvanized Trailer Axle with a Galvanized Tie Plate Kit.

- This item is mounted to the 1500 lb Black Powder Coated Trailer Axle with a Zinc Tie Plate Kit. 

MODEL: CFAXLE-LSPRNG(3-SF)

MPN: TDE 13087 or Dexter 072-13087

Note: Springs will be replaced with Dexter 072-119-00 750lb 3-Leaf Springs in the near future.

Specifications

Length: 24.63"

Leaf Width: 1.75"

Arch Height: 4.50"

Bushing Type: Nylon

Used on

General

2000 lb Extended Galvanized PWC Trailer Axle w/ 545 Hubs and Springs

*This item is not shipped! Pickup only from our location at 2375 Pleasantdale Rd. Atlanta, GA 30340*

*NOTE: if your trailer is older than 2006, call before ordering to ensure you receive the correct axle.*

Materials Include:

1 - 84.45" x 1.5" x 1.5" x 11 Gauge Galvanized Axle Tubing 

2 - Galvanized 5-Bolt Hub Assembly

2 - 4-Leaf Slipper Springs (1250 lb)

1 - Galvanized Tie Plate Kit

This item is mounted to the PWT-2212G trailer model with a Galvanized Axle Mounting Kit, and to the PWT-2212B trailer model with a Black Powder Coated Axle Mounting Kit

MODEL: CFAXLE2000G-EXTENDED

Specifications

Tubing: 1.5" Galvanized Square Axle

Load Rating: 2000 lb

Hub Face: 91.5"

Spring Center: 81.5"

Overall Length: 56"

Bearing Size: 1-1/16"

Used on

General

21' 4-Pin Wishbone Wire Harness Assembled w/ Protective Sleeve

The wiring is pulled through the trailer frame to provide connection between the lighting and the vehicle. It connects to the vehicle with a 4-Pin Male Connector. This item comes with a 3/8 20" Protective Sleeve and 30" Ground with 1/2" ring terminal.

Since April 2026, our trailers use 1/4 Ring Terminals and a longer Ground Wire to secure the lighting in a different position than previous seasons' models. Those will be denoted with a -R1/4 suffix to the part in lieu of the -R1/2 currently.

MODEL: CFWH21-R1/2

Used on

JBT-1600 (EXT) (formerly JBT-1600 ‘RIVER HAWK’)

General

3/8″- 16 Galvanized Tri-Lock Nut

This item pairs with any 3/8"-16 Thread Galvanized Bolt or U-Bolt.

This item is part of these kits:

– Galvanized Winch Assembly Mounting Kit

– Galvanized Tie Plate Kit for 1.5" Square Axle Tubing

– 1000G - Bunk Mounting Kit

– 2212G - Bunk Mounting Kit

– 2212G - Fender Mounting Kit

– 2213G - Bunk Mounting Kit

– 2213G - Fender Mounting Kit

– Jon Boat Trailer Bunk Mounting Kit

– Jon Boat Trailer Fender Mounting Kit

– Jon Boat Trailer Bow Support Bunk Mounting Kit

– 'River Hawk' Jon Boat Trailer Bunk Mounting Kit

MODEL: CFNUT3/8TRILOCK

Used on

General

Phoenix Stamping Angle Swivel Bracket, Galvanized - 7/16″ Top Hole

These are used to mount bunk boards onto all Jon Boat, and PWT Trailer models.

This item is part of these kits:

- 1000B/1100B - Bunk Mounting Kit

- 1000G/1100G - Bunk Mounting Kit

- 2212B - Bunk Mounting Kit

- 2212G - Bunk Mounting Kit

- 2213B/2214B - Bunk Mounting Kit

- 2213G/2214G - Bunk Mounting Kit

- Jon Boat Trailer Bunk Mounting Kit

- Jon Boat Trailer Bow Support Mounting Kit

- Extended (EXT)/'River Hawk' Jon Boat Trailer Bunk Mounting Kit

MODEL: CFBRKTSWIVEL

MPN: PS-BB06G

Used on

PWT-1000B (Obsolete as of 2023)

PWT-1000G (Obsolete as of 2023)

PWT-2213B (Obsolete as of 2023)

PWT-2213G (Obsolete as of 2023)

General

Winch Poly Bow Roller Assembly

This kit is part of every Winch Assembly used on every PWT, and Jon Boat Trailer model. 

Materials Include:

1 – Galvanized Bow Stop Bracket

1 – 3/8″-16 x 3.75″ Zinc Hex Head Cap Bolt

1 – 3/8″-16 Zinc Hex Flange Top Lock Nut

1 – 1/2″-13 x 4.5″ Zinc Hex Head Cap Bolt

1 – 1/2″-13 Zinc Top Lock Nut

1 – 3″ Amber Poly Bow Roller

2 – 3″ Amber Poly Bow Roller Bell End

2 – 1/2″- Zinc Flat Washer

MODEL: CFASSM-WNCHRLR(3)

Used on

General

Galvanized Tie Plate Kit for 1.5" Square Trailer Axles

This kit is used to mount springs to Galvanized 1.5" Square Trailer Axles. The kit is a part of the 1500 lb Galvanized Trailer Axle used on every PWT-1000G, and PWT-1100G trailer model. It is also part of the 1500 lb Extended Galvanized Trailer Axle used on both PWT-2212 trailer models.

Materials Include:

2 - Galvanized Axle Tie Plate for 1.5" Square Trailer Axle

4 - 3/8"-16 x 1.56" x 3.63" Galvanized U-Bolt

8 - 3/8"-16 Galvanized Tri-Lock Nut

8 - 3/8" Galvanized Lock Washer

MODEL: CFAXLEKIT-SPRNGMNT(1.5K-G)

Used on

General

3/8"-16 Zinc Hex Flange Top Lock Nut Zinc

This item is part of the:

– 1000B - Bunk Mounting Kit

– 2212B - Fender Mounting Kit

– 2213B - Fender Mounting Kit

– Winch Poly Bow Roller Assembly

– Pontoon Boat Trailer Winch Assembly

MODEL: CFNUT3/8LOCKZ

Used on

ALL COM-FAB TRAILER MODELS

General

5/16″ x 1-1/2″ Galvanized Hex Head Lag Screw

It is used for mounting Bunk Boards to Galvanized Angular Swivel Brackets, and Pontoon Boat Trailer Bunk Brackets on all trailer models.

MODEL: CFSCRWLAG-5/16-0150

Used on

ALL COM-FAB TRAILER MODELS

General

Galvanized Axle Mounting Kit

This kit is used to mount Complete Galvanized Axles to all PWT, and Jon Boat Trailer models.

Materials Include: 

2 - 1/2" x 3" Galvanized Hex Head Bolt

2 - 1/2"-13 Galvanized Tri-Lock Nuts

MODEL: CFAXLEMNTKITG

Used on

General

5/32" x 2" Cotter Pin, Zinc-Plated for Axle Spindle Hubs

It is used for fastening the Castle Nut to the Axle Spindle.

MODEL: CFAXLE-PIN(COTTER)

MPN: Dexter 019-10560

Used on

ALL COM-FAB TRAILER MODELS

General

3/8″-16 x 3.06" x 2.38″ Galvanized U-Bolt 

This item is a part of these kits:

- 2213G - Bunk Mounting Kit

- 2212G - Bunk Mounting Kit

- 2212G - Fender Mounting Kit

- Jon Boat Trailer Bunk Mounting Kit

- Jon Boat Trailer Fender Mounting Kit

- 'River Hawk' Jon Boat Trailer Bunk Mounting Kit

MODEL: CFUBLT3/8x3.06x2.38G

MPN: TDE 83027G

Used on

General

5" x 1.25" x .25" Galvanized Flat Plate w/ 2 9/16" Holes and 3.5" Hole Centers

This item is part of these kits:

– Galvanized Winch Assembly Mounting Kit

– 2212G - Fender Mounting Kit (pre-April 2024 Models)

– 2212G - Bunk Mounting Kit

– Jon Boat Trailer Winch Assembly Mounting Kit

– Jon Boat Trailer Fender Mounting Kit

– Jon Boat Trailer Bow Support Mounting Kit

MODEL: CFFLTSTRPWNCHG

Used on