PWT-1000B Parts

General

3.06″ Wide Rubber Grommet for Steel E-Z Lube/SuperLube Grease Dust Cap

This item is used in conjunction with a 2" Dust Cap as part of both Hub Assemblies.

2″ Steel Super Lube Grease Dust Cap & Plug

Galvanized 5-Bolt Hub Assembly

Powder Coated Black 5-Bolt Hub Assembly

MODEL: CFAXLE-PLUG

MPN: Dexter 085-001-00 or TDE 46963

Used on

ALL COM-FAB TRAILER MODELS

General

12-Sided/Position Axle Cone Castle Nut, 1"-14 Thread

This item is fastened to the end of an Axle Spindle with the use of a 5/32" x 2" Zinc Plated Cotter Pin. This combination secures Hubs to all PWC Trailer Models. It is rated for axles less than 3000 lbs. It is a 1"-14 Thread 12-Slot Castle Nut to fit standard 1" trailer spindles.

MODEL: CFAXLE-NUT(CASTLE-L)

MPN: Dexter 006-10634 or TDE 10634

Used on

General

4" x 1" x .25" Zinc Flat Plate w/ 1/2" Holes and a 2.5" Hole Center - Shackle Link

- This item is part of the CFBNKKIT-PWT(SGL-PC) used to mount Bunk Boards onto PWT-800B, PWT-1000B, and PWT-1100B trailer models.

MODEL: CFFLTSTRPBUNK(SGL)Z

Used on

General

1-1/16" L44649 Tapered Axle Bearings

These bearings fit a 1-1/16" diameter Spindle Shaft, and are used with L44610 Bearing Cups. These are used on Tie-Down #1350, and #1750 Hubs

MODEL: CFAXLE-BRG(1-1/16")-INNER/OUTER

UNIVERSAL MODEL: L44649

MPN: TDE 11054 or Dexter 031-031-02

Used on

ALL COM-FAB PWC, JON BOAT, AND CANOE/KAYAK TRAILER MODELS

General

Side Crank Swivel Jack Mounting Kit

This kit contains all of the  parts needed to mount the 1200 lb Side Crank Swivel Jack, as well as the 1500 lb Side Crank Swivel Jack to all trailer frame models

MODEL: CFJACK-MNTKIT

Used on

ALL COM-FAB TRAILER MODELS

General

1/2″-20 Lug Nut (Set of 5)

These are used for mounting tires on all trailer models to 1 1/2"-20 Threaded Stud.

MODEL: CFNUTLUG

Used on

ALL COM-FAB TRAILER MODELS WITH SILVER E-COAT OR GALVANIZED WHEELS

General

- Two of these are used with 1/4″ Zinc Nuts to mount TecNiq 8 Function 6" LED Tail Lights & TecNiq 7 Function 6" LED Tail Lights to all current Com-Fab Trailer Models

- Two of these are used with 1/4″ Zinc Nuts to mount Dry Launch Submersible Tail Lights to Pre-2018 Com-Fab trailer models.

MODEL: CFBLTLIGHT

Used On

ALL COM-FAB TRAILER MODELS

General

3/8”-16 x 2.06” x 2.88” Zinc U-Bolt

This item is part of the 1000B - Bunk Mounting Kit used to mount bunks onto PWT-800B, PWT-1000B, AND PWT-1100B trailer models.

MODEL: CFUBLT3/8x2.06x2.88Z

MPN: TDE 83028Z

Used on

General

15″ Powder Coated Black Winch Post

This item is used to create 15" Black Powder Coated Winch Assemblies (Smooth High Gloss Bengal) for Single Black Powder Coated PWT Trailers (Smooth High Gloss Bengal).

15″ Black Powder Coated Winch Assembly w/ DL 600LB Winch

MODEL: CFWNCHPOST(PWC-15)-B (BENGAL)

Used on

General

Zinc Tie Plate Kit for 1.5" Square Trailer Axle

- This kit is used to mount springs 1.5" Square Trailer Axles.

- This kit is part of both 1000 lb Trailer Axles used on the PWT-800, and Jon Boat Trailer models.

-This kit is also part of the 1500 lb Black Powder Coated Trailer Axle used on the PWT-1000B, and the PWT-1100B.

Materials Include:

2 - Zinc Axle Tie Plate for 1.5" Square Trailer Axle

4 - 3/8"-16 x 1.56" x 3.63" Zinc U-Bolt

8 - 3/8"-16 Zinc Nylock Nut

MODEL: CFAXLEKIT-SPRNGMNT(1.5K-Z)

Used on

General

Black Powder Coated Axle Mounting Kit

This kit is used to mount Black Powder Coated Axles to Black Powder Coated PWT Trailer models.

Materials Include: 

2 - 1/2" x 3" Zinc Hex Head Bolt

2 - 1/2"-13 Zinc Flange Top Lock Nut

MODEL: CFAXLEKIT-MOUNT(Z)

Used on

General

Company Graphic for Single PWT and Jon Boat Trailers

This graphic sticks to the side of all Single PWT, Jon Boat, and PWT-2212 trailer models with Sides of 3" tall Tubing. 

Dimensions: 19.75" x 2"

MODEL: CFGRAPHIC-(3X1.5)

Used on

General

Coupler Mounting Kit for 3" Wide Trailer Tongues

This item is used to mount Couplers to all trailer models without Brakes.

Materials Include: 

2 - 1/2″-13 x 4″ Zinc Hex Head Cap Bolt

2 - 1/2″- 13 Zinc Top Lock Nut

MODEL: CFCPLR-MNTKIT(NONBRK)

Used on

ALL COM-FAB TRAILER MODELS

General

Black Marine Carpet 10.25" Width

$2/ft in 100 ft rolls

- This carpet is used for bunks on all of our PWC Trailer, and Jon Boat Trailer models. It is optional for our Pontoon Trailer models and Canoe/Kayak Angler Kits.

If you are purchasing this carpet it needs to be a foot longer than the board itself.

This carpet comes in these specific sizes as well:

- 5 ft Bunk Board Black Marine Carpet

- 6 ft Bunk Board Black Marine Carpet

- 7 ft Bunk Board Black Marine Carpet

MODEL: CFBNKCOVER-CARPET(10.25)

Used on

Optional for

c-General

3/8"-16 Thread Nylock Nut, Zinc-Plated

This item is part of the Zinc Tie Plate Kit used to mount 2-Leaf Slipper Springs (550 lb), and 3-Leaf Slipper Springs (750 lb) to 1.5" Square Axle Tubing.

MODEL: CFAXLE-NUT(3/8NYLOCK-Z)

Used on

General

3/8"-16 x 1.56" x 3.63" U-Bolt, Zinc-Plated - For Standard 1.5" SQ Tubing Axles

This item is part of the Zinc Axle Tie Plate Kit used to mount 2-Leaf Slipper Springs (550 lb), and 3-Leaf Slipper Springs (750 lb) to 1.5" Square Axle Tubing.

MODEL: CFAXLE-UBLT(1.5SQ-Z)

MPN: TDE 83002-1Z

Used on

General

Axle Tie Plate, Zinc-Plated for 1.5" Square Trailer Axle (Powder Coat, up to 2000lb Axles)

- This item is part of the Zinc Tie Plate Kit used to mount 3-Leaf Slipper Springs (750 lb) to Black Powder Coated 1.5" Square Axle Tubing used on PWT-1000B, and PWT-1100B trailer models.

- The same kit is used to mount 2-Leaf Slipper Springs (550 lb) to Black Powder Coated 1.5" Square Axle Tubing used on the PWT-800 model.

Specifications

Axle Size: 1-1/2" Square Axle

U-Bolt Size: 3/8"-16 x 1.56 x 3.63

Dimensions: 3" x 3" x .21"

Tube Width: 2"

Spring Width: 1-3/4"

Hole Diameter: 7/16"

U-Bolt Finish: Zinc

Plate Finish: Zinc

Used on

General

Zinc U Bolt Winch Assembly Mounting Kit for Black Powder Coated Trailers

This kit has all of the requisite materials needed to mount a Black Powder Coated Winch Assembly onto any Black Powder Coated PWT trailer model.

Materials Include:

2 – 3/8″-16 x 3" x 4.5″ Zinc U-Bolt

2 – 5" x 1.25" x .25" Zinc Flat Plate

4 – 3/8″-16 Zinc Plated Serrated Flange Nuts

MODEL: CFWNCHKIT-(PWC-Z)

Used on

General

3" Poly Bow Roller Assembly

This is a section of the Winch Poly Bow Roller Assembly.

Materials Include:

1 – 3″ Poly Bow Roller 
2 – 3″ Poly Bow Roller Bell End
1 – 1/2″-13 x 4.5″ Zinc Bolt
2 – 1/2″ Zinc Flat Washer
1 – 1/2″-13 Top Lock Nut

MODEL: CFASSM-POLYRLR(3)

Used on

General

1/4″-20 Thread External Tooth Locknut, Zinc Nut for Tail Lights

- Two of these are used with 1/4″- 20 Tail Light Bolts to mount TecNiq 8 Function 6" LED Tail Lights to all current Com-Fab Trailer models.

- Two of these are used with 1/4″- 20 Tail Light Bolts to mount Dry Launch SP7 Red Tail Lights to all Pre-2018 Com-Fab trailer models.

- One of these is used w/ 2-3/4"-20 Thread Bolts to secure PWT winch strap to crank winch.

MODEL: CFNUT1/4LOCKZ

Used on

ALL COM-FAB TRAILER MODELS

General

3/8″-16 Serrated Zinc Flange Nut

This item is part of these kits:

- 3/8"-16 Zinc Hex Head Bolts to mount all Crank Winch Models onto all Winch Post models.

- Black Powder Coated Winch Assembly Mounting Kit

- Jon Boat Trailer Winch Assembly Mounting Kit

MODEL: CFNUT3/8SERTDZ

Used on

ALL Powder Coat Finish Trailer Models, and Most Galvanized Trailer Models for Winches

General

5"x 1.25" x .25" Zinc Flat Plate w/ 2 9/16" Holes and 3.5" Hole Centers

This item is part of these kits:

- Black Powder Coated Winch Assembly Mounting Kit

- 2212B - Fender Mounting Kit (pre-April 2024 Models)

- 2212B - Bunk Mounting Kit.

MODEL: CFFLTSTRPWNCHZ

Used on

General

3/8″-16 x 1″ Zinc Hex Head Cap Bolt

This item is used with 3/8"-16 Serrated Zinc Flange Nuts to mount all crank winch models onto every type of winch post. It is also part of the 2213B - Bunk Mounting Kit used to mount bunks onto PWT-2213B, and PWT-2214B trailer models. 

MODEL: CFBLT3/8X1Z

Used on

ALL COM-FAB TRAILER MODELS

General

3/8″-16 x 3.06" x 4.5″ Zinc U-Bolt

This item is part of the Black Powder Coated Winch Assembly Mounting Kit used to mount all Black Powder Coated Winch Assemblies to all Black Powder Coated PWT trailer models.

MODEL: CFUBLT3/8x3.06x4.5Z

MPN: TDE 83364Z

Used on