PT-2426 Parts

General

Coupler Mounting Kit for 3" Wide Trailer Tongues

This item is used to mount Couplers to all trailer models without Brakes.

Materials Include: 

2 - 1/2″-13 x 4″ Zinc Hex Head Cap Bolt

2 - 1/2″- 13 Zinc Top Lock Nut

MODEL: CFCPLR-MNTKIT(NONBRK)

Used on

ALL COM-FAB TRAILER MODELS

General

288″ Black Flex Hose Male-Banjo Brake Line - Dexter

This item is used for brake lines on select PT-2426 models only.

For use with:

– Banjo Fitting Base
– Square Banjo Fitting Bolt
– Black O-Ring
– Copper Banjo Fitting Washer

TIE DOWN MODEL: #46238-288

MODEL: CFBRKELINE-288(BLK)

Used on

PT-2426

General

Pontoon Boat Trailer Tandem Axle Fender Mounting Kit

This kit contains all of the requisite materials needed to mount a Tandem Axle Galvanized Pontoon Boat Trailer Fender onto all Tandem Axle Pontoon Boat Trailer models.

Materials Include:

4 – 3/8″-16 x 4.19″ x 3″ Galvanized U-Bolt

4 – 6" x 1.5" x 1.25" Galvanized Flat Plate

8 – 3/8″ Galvanized Tri-Lock Hex Nuts

MODEL: CFFNDRKIT-PTG(TA)

Used on

General

Dry Launch Amber Side Marker Light w/ 10" of Wire

This item is a Dry Launch 203 Series with a snap out bulb slide. You can change the bulb without tools, and mount it with a single stud. It can be used as a Side Marker Light for the tongue of all Pontoon Boat Trailer models.

MODEL: CFLIGHTSDMRKR-10

Optional for

General

7000# Galvanized Axle Tie Plate w/ 4.49" x 3.5" Dimensions for 2" Tubing and 1.75" Spring Width

This item is part of the 7000# Galvanized Tie Plate Kit used to mount 3-Leaf Double Eye Springs on to 3500 lb Hydraulic Disc Brake Trailer Axles, or 2900 lb Idler Trailer Axles.

TIE DOWN MODEL: 44849DG

MODEL: CFAXLE-TIEPLATE(7000-G)

Specifications

Axle Size: 2" x 2" Square Axle

U-Bolt Size: 1/2"-13 x 2.06" x 4.31"

Dimensions: 4.49" x 3.5"

Tube Width: 2"

Spring Width: 1-3/4"

Hole Diameter: 9/16"

U-Bolt Finish: Galvanized

Plate Finish: Galvanized

Used on

General

3/8" Black Cable Clamp for Brake Lines

This item is secured onto the axle w/ use of a 12 x 3/4″ Zinc Hex Washer Head Tek#3 Screw. The item is used for securing all brake lines to axles on Pontoon Boat Trailer models w/ Brakes.

MODEL: CFBRKECBLCLAMP

Used on

General

Tie Down 1/2" x 2-5/8" Disc Brake Caliper Slider Pin

This item is used for mounting a Tie Down caliper to a 9.6" vented rotor. Stainless steel caliper slide pins are easily accessible with hex heads for quick removal. It allows the caliper to float freely and insures proper alignment during installation. It fits all vented rotor calipers.

TIE DOWN MODEL: 44676G

MODEL: CFAXLE-PIN(SLIDER)

Used on

General

Flat Pontoon Bunk Bracket #44879

Length: 9.02"

Base Length: 8.38"

Width: 3"

Height: 5.25"

Optional for

General

Heavy Duty Pontoon Bunk Bracket #43747

This item is optional for all Pontoon Boat Trailer models. It fits 2' x 4' and 2' x 6' boards.

Specifications

Length: 15.4"

Base Length: 13.13"

Width: 3"

Height: 6.07"

Optional for

General

9/16"-18 x 3" Shackle Bolt

- This item is part of the Pontoon Boat Trailer Single Axle Mounting Kit used to mount 3500 lb Hydraulic Disc Brake Trailer Axles, or 2900 lb Idler Trailer Axles to all Single Axle Pontoon Boat Trailer models.

- This item is part of the Pontoon Boat Trailer Tandem Axle Mounting Kit used to mount two 3500 lb Hydraulic Disc Brake Trailer Axles, or 2900 lb Idler Trailer Axles to all Tandem Axle Pontoon Boat Trailer models.

MODEL: CFAXLE-BLT(SHACKLE-Z)

Used on

General

3/8″-16 x 2.06″ x 5.25″ Zinc U-Bolt

This item is used with a 4" x 1" x .25" Galvanized Flat Plates w/ 1/2" Holes, and a 3/8"-16 Serrated Zinc Flange Nuts to mount Pontoon Boat Trailer Bunk Brackets onto all Pontoon Boat Trailer models.

See: Tall Galvanized Pontoon Boat Trailer Bunk Bracket Kit

MODEL: CFUBLT3/8X2.06X5.25Z

Used on

General

3.75" x 1.25" x .25" Zinc Steel Shackle Link w/ 9/16" Holes - Replacement Standard Shackle Link

These are used to mount 2900 lb Idler Trailer Axles, or 3500 lb Hydraulic Disc Brake Trailer Axles to frames on all Single and Tandem Axle setups for Pontoon Boat trailers, and are frequently used in conjunction with axle equalizers.

Pontoon Boat Trailer Single Axle Mounting Kit

Pontoon Boat Trailer Tandem Axle Mounting Kit

TIE DOWN MODEL: #44536

MODEL: CFAXLELINK(Z)

Used on

General

84″ Grey Flex Hose Banjo-Banjo Brake Line - Dexter

This item is used to connect two Aluminum E-Coat Caliper Assemblies on Tandem Axle Pontoon Boat Trailers. 

MODEL: CFBRKELINE-84BB(GREY)

Used on

 General

264″ Grey Poly Flex Hose Male-Banjo Brake Line - Dexter

This item is used as a brake line on PT-2426 models only.

For use with:

– Banjo Fitting Base
– Square Banjo Fitting Bolt
– Black O-Ring
– Copper Banjo Fitting Washer

TIE DOWN MODEL: #46223-264

MODEL: CFBRKELINE-264B(GREY)

Used on

PT-2426

General

Copper Banjo Brake Fitting Washer

This item is used in conjunction with 64" Grey Flex Hose Banjo-Banjo Brake Lines, Brass Banjo Fitting Bolts, and Black O-Rings to connect Aluminum E-Coat Caliber Assemblies on all tandem axle pontoon trailer models.

For use with: 

– 64″ Grey Flex Hose Banjo-Banjo Brake Lines
– Brass Banjo Fitting Bolts
– Black O-Rings

MODEL: CFBRKE-WSHRBANJO

Used on

General

3/8″-16 x 4.19″ x 3″ Galvanized U-Bolt

This item is part of the 2213G - Fender Mounting Kit used to mount fenders to PWT-2213G, PWT-2214G, and all Pontoon Boat Trailer models.

MODEL: CFUBLT3/8X3.00G

Used on

General

Tandem Axle Galvanized Pontoon Boat Trailer Fender with Welded-On Spring Hangers

This item is not shipped! Pickup only from our location at 2375 Pleasantdale Rd. Atlanta, GA 30340 

- This item is mounted to Pontoon Boat Trailer frames with a Pontoon Boat Trailer Tandem Axle Fender Mounting Kit, and it typically uses an ST175/80D13 C Load Range 13″ Galvanized Tire & Wheel.

- The hangers welded to bottom are for mounting two 2900 lb Idler Trailer Axles, or two 3500 lb Hydraulic Disc Brake Trailer Axles with a Pontoon Boat Trailer Tandem Axle Mounting Kit.

MODEL: CFFNDRPT(TA-G)

Used on

General

Axle Equalizer

Two of these axle equalizers are part of the Pontoon Boat Trailer Tandem Axle Mounting Kit used to mount 3-Leaf Double Eye Springs to frames on all Tandem Axle Setups for Pontoon Boat Trailers

MODEL: CFAXLE-EQUALIZER

Used on

General

Galvanized Side Mount Spare Tire Carrier

• This item is optional for all of our Galvanized Trailer models.
• It can accommodate wheels from 10" to 16.5" with a spare tire.
• It fits all 4 and 5 lug wheels with 4" and 4.5" diameter hole patterns.
• The galvanized finish provides long lasting protection.
• The item can mount to trailer frames up to 3" wide and 4" high. 

*Used on Galvanized Trailer Models Only

TIEDOWN MODEL: #86098

MODEL: CFSTB-SIDE(G)

Installation Instructions

1. Using the spare tire carrier and spare tire as a guide, determine a suitable mounting location on trailer frame.

2. Slide U-bolt around the frame and through the holes in tire carrier.

3. Mount with flat washers, lock washers and nuts provided.

4. Using the spare tire to determine the correct holes to use, place the carriage bolts provided for mounting the spare tire in the holes of the rectangular plate. Bolt heads should be on the back side of the tire carrier. Secure bolts with “star” washers.

5. The mounting plate will accommodate several sizes of frames by using the various hole patterns.

6. Check position of the tire mount for proper clearance with the spare tire before tightening bolts.

7. Mount spare tire with 1/2" bolt, washers and hex nuts provided.

Optional for

ALL GALVANIZED TRAILER MODELS

General

2x2 Square Tubing Plug for 10-14 GA

This item is used on Pontoon Winch Stands & Canoe/Kayak Crossbars and Uprights. It may also be used in other applications utilizing 2" square tubing.

This item is part of these kits:

- 2 Capacity Canoe/Kayak Kit

- 3 Capacity Canoe/Kayak Kit

- 4 Capacity Canoe/Kayak Kit

- 2 Canoe + 2 Kayak Kit

- 6 Capacity Canoe/Kayak Kit

MODEL: CFCAP-2X2(10-14GA)

Used On

General

2x4 Rectangular Tubing Plug for 10-14 GA

This item is used on Pontoon Winch Stands and as End Caps to the 2x4 Tubing of Pontoon Trailers.

MODEL: CFCAP-2X4(10-14GA)

Used On

General

1500 lb Side Crank Swivel Jack - Dutton-Lainson

• Dutton-Lainson swivel marine tongue jack for boat and other trailer applications
• 1,500 lb. capacity
• 24-3/4" maximum tongue height
• Side wind handle with extra heavy screw drive and ergonomic handle grip
• Heavy duty polypropylene 8" diameter slotted wheel resists flat spots and cold weather cracking
• Zinc plated finish for additional rust resistance and longer life
• Easily swivels up for towing or down for stowing and locks in place in either position
• Reinforced wheel bracket for additional strength
• Includes all necessary bolt-on mounting hardware
• Made in the U.S.A.

Dutton-Lainson Model: 6850

MODEL: CFJACKSIDE-6850

Used On

PT-2224
PT-2426
PT-2628

General

64″ Grey Flex Hose Banjo-Banjo Brake Line - Dexter

This item is used to connect two Aluminum E-Coat Caliper Assemblies on Tandem Axle Pontoon Boat Trailer models. 

For use with:

Used on

General

Weld Aid B-100 Brite Zinc Aerosol Spray Can

This product is used to touch up, and prevent rust and corrosion on all of our galvanized items for sale. The spray is 69% Zinc Metal ensuring that it matches the shine of any and all Hot-Dipped Galvanized Steel. It has a special no clog nozzle, and can cover up to 40 sq feet of steel. This item meets ASTM-A780 requirements for corrosion protection.

Read the Safety Instructions carefully before use of this item.

https://weldaid.com/wp-content/uploads/2018/11/1008302E.pdf

Specifications

Part No: B-100

UPC: 731592100013

Volume: 12.5 oz Primer

Model: CFGALVSPRAY

Used On