Parts

General

Galvanized Side Mount Spare Tire Carrier

• This item is optional for all of our Galvanized Trailer models.
• It can accommodate wheels from 10" to 16.5" with a spare tire.
• It fits all 4 and 5 lug wheels with 4" and 4.5" diameter hole patterns.
• The galvanized finish provides long lasting protection.
• The item can mount to trailer frames up to 3" wide and 4" high. 

*Used on Galvanized Trailer Models Only

TIEDOWN MODEL: #86098

MODEL: CFSTB-SIDE(G)

Installation Instructions

1. Using the spare tire carrier and spare tire as a guide, determine a suitable mounting location on trailer frame.

2. Slide U-bolt around the frame and through the holes in tire carrier.

3. Mount with flat washers, lock washers and nuts provided.

4. Using the spare tire to determine the correct holes to use, place the carriage bolts provided for mounting the spare tire in the holes of the rectangular plate. Bolt heads should be on the back side of the tire carrier. Secure bolts with “star” washers.

5. The mounting plate will accommodate several sizes of frames by using the various hole patterns.

6. Check position of the tire mount for proper clearance with the spare tire before tightening bolts.

7. Mount spare tire with 1/2" bolt, washers and hex nuts provided.

Optional for

ALL GALVANIZED TRAILER MODELS

General

5/16″ x 1-1/2″ Galvanized Hex Head Lag Screw

It is used for mounting Bunk Boards to Galvanized Angular Swivel Brackets, and Pontoon Boat Trailer Bunk Brackets on all trailer models.

MODEL: CFSCRWLAG-5/16-0150

Used on

ALL COM-FAB TRAILER MODELS

General

Locking Spare Tire Bracket, fits 3″ Width Tubing

This item is used to lock down, and transport a spare tire on all Com-Fab trailer models. Lock not included.

MODEL: CFSTB-TOP

Optional for

ALL COM-FAB TRAILER MODELS

General

1/2″-20 Lug Nut (Set of 5)

These are used for mounting tires on all trailer models to 1 1/2"-20 Threaded Stud.

MODEL: CFNUTLUG

Used on

ALL COM-FAB TRAILER MODELS WITH SILVER E-COAT OR GALVANIZED WHEELS

General

Tie Down 7/16" Diameter x 2.593 Stainless Steel Slider Pin

This item is used for mounting a Tie Down caliper to a 9.6" vented rotor. Stainless steel caliper slide pins are easily accessible with hex heads for quick removal. It allows the caliper to float freely and insures proper alignment during installation. It fits all vented rotor calipers.

TIEDOWN MODEL #007-692-00 or 12114

MODEL: CFAXLE-PIN(CALIPER-SS)

Used on

General

Black Powder Coated Side Mount Spare Tire Carrier

• This item is optional for all of our Black Powder Coated Trailer models.
• It can accommodate wheels from 10" to 16.5" with a spare tire.
• It fits all 4 and 5 lug wheels with 4" and 4.5" diameter hole patterns.
• The powder coated finish provides long lasting protection.
• The item can mount to trailer frames up to 3" wide and 4" high.
  

*Used on Black Powder Coated Trailer Models Only

TIEDOWN MODEL: #86100

MODEL: CFSTB-SIDE(B)

Installation Instructions

1. Using the spare tire carrier and spare tire as a guide, determine a suitable mounting location on trailer frame.

2. Slide U-bolt around the frame and through the holes in tire carrier.

3. Mount with flat washers, lock washers and nuts provided.

4. Using the spare tire to determine the correct holes to use, place the carriage bolts provided for mounting the spare tire in the holes of the rectangular plate. Bolt heads should be on the back side of the tire carrier. Secure bolts with “star” washers.

5. The mounting plate will accommodate several sizes of frames by using the various hole patterns.

6. Check position of the tire mount for proper clearance with the spare tire before tightening bolts.

7. Mount spare tire with 1/2" bolt, washers and hex nuts provided.

Optional for

ALL BLACK POWDER COATED TRAILER MODELS

General

3/8″-16 x 3.06" x 2.38″ Galvanized U-Bolt 

This item is a part of these kits:

- 2213G - Bunk Mounting Kit

- 2212G - Bunk Mounting Kit

- 2212G - Fender Mounting Kit

- Jon Boat Trailer Bunk Mounting Kit

- Jon Boat Trailer Fender Mounting Kit

- 'River Hawk' Jon Boat Trailer Bunk Mounting Kit

TIE DOWN MODEL: #83027G

MODEL: CFUBLT3/8X2.38G

Used on

General

Galvanized Angular Swivel Bracket - 7/16″ Top Hole

These are used to mount bunk boards onto all Jon Boat, and PWT Trailer models.

This item is part of these kits:

- 1000B - Bunk Mounting Kit

- 1000G - Bunk Mounting Kit

- 2212B - Bunk Mounting Kit

- 2212G - Bunk Mounting Kit

- 2213B - Bunk Mounting Kit

- 2213G - Bunk Mounting Kit

- Jon Boat Trailer Bunk Mounting Kit

- Jon Boat Trailer Bow Support Mounting Kit

- 'River Hawk' Jon Boat Trailer Bunk Mounting Kit

MODEL: CFBRKTSWIVEL

Used on

General

Galvanized Bow Stop Bracket

This item is part of the Winch Poly Bow Roller Assembly used on every type of winch stand for all Jon Boat, and PWT trailer models.

MODEL: CFBRKTWNCHRLR

Used on

General

3/8"-16 Zinc Hex Flange Top Lock Nut Zinc

This item is part of the:

– 1000B - Bunk Mounting Kit

– 2212B - Fender Mounting Kit

– 2213B - Fender Mounting Kit

– Winch Poly Bow Roller Assembly

– Pontoon Boat Trailer Winch Assembly

MODEL: CFNUT3/8LOCKZ

Used on

ALL COM-FAB TRAILER MODELS

General

3/8"-16 x 2.06" x 2.88" Galvanized U-Bolt

This item is part of the 1000G Bunk Mounting Kit used to mount bunks to PWT-800G, PWT-1000G, AND PWT-1100G trailer models.

MODEL: CFUBLT3/8X2.88G

Used on

General

4" x 1" x .25" Galvanized Flat Plate w/ 2 1/2" Holes and a 2.5" Hole Center - Shackle Link

- This item is part of the 1000G - Bunk Mounting Kit to mount Bunk Boards onto PWT-800G, PWT-1000G, and PWT-1100G trailer models.

- This item is part of the Tall Galvanized Bunk Bracket Kit used to mount mount 2″ x 4″ or 2″ x 6″ bunk boards on all Pontoon Boat Trailer models.

MODEL: CFFLTSTRPBUNK(SGL)G

Used on

General

3/8″-16 x 2.06″ x 5.25″ Zinc U-Bolt

This item is used with a 4" x 1" x .25" Galvanized Flat Plates w/ 1/2" Holes, and a 3/8"-16 Serrated Zinc Flange Nuts to mount Pontoon Boat Trailer Bunk Brackets onto all Pontoon Boat Trailer models.

See: Tall Galvanized Pontoon Boat Trailer Bunk Bracket Kit

MODEL: CFUBLT3/8X2.06X5.25Z

Used on

General

1-1/2"-20 Lug Nut Stud

The stud material is SAE grade 8, zinc dichromate plated, with a minimum 96 hour salt spray requirement. 

1/2"-20 Lug Nut

MODEL: CFAXLE-BLT(STUD1-1/2)

Used For

ALL COM-FAB TRAILER MODELS

General

3/8″-16 x 1″ Zinc Hex Head Cap Bolt

This item is used with 3/8"-16 Serrated Zinc Flange Nuts to mount all crank winch models onto every type of winch post. It is also part of the 2213B - Bunk Mounting Kit used to mount bunks onto PWT-2213B, and PWT-2214B trailer models. 

MODEL: CFBLT3/8X1Z

Used on

ALL COM-FAB TRAILER MODELS

General

8.25" x 1.5" x .25" Galvanized Flat Plate w/ 7/16" Holes and 3.5" Hole Centers - Shackle Link

This item is part of the 2213G - Bunk Board Mounting Kit used to mount Bunk Boards onto PWT-2213G, and PWT-2214G trailer models.

MODEL: CFFLTSTRPBUNK(DBL)G

Used on

General

3/8″-16 x 3.06" x 4.5″ Galvanized U-Bolt

This item is part of these kits:

- Galvanized Winch Assembly Mounting Kit

- Jon Boat Trailer Bow Support Bunk Mounting Kit

MODEL: CFUBLT3/8X4.5G

Used on

General

3/8"-16 x 1.56" x 3.63" Galvanized U-Bolt - For Standard 1.5" SQ Tubing Axles

This item is part of the Galvanized Tie Plate Kit used to mount 3-Leaf Slipper Springs to Galvanized 1.5" Square Axle Tubing.

TIE DOWN MODEL: #83002G

MODEL: CFAXLE-UBLT(1.5SQ-G)

Used on

General

8″ Galvanized Adjustable Bolster Bunk Bracket

This item is part of these kits:

- Jon Boat Trailer Bunk Mounting Kit

- Jon Boat Trailer Bow Support Mounting Kit

- 'River Hawk' Jon Boat Trailer Bunk Mounting Kit

TIE DOWN MODEL: 86130G

MODEL: CFBRKTBLSTR

Used on

General

3/8”-16 x 2.06” x 2.88” Zinc U-Bolt

This item is part of the 1000B - Bunk Mounting Kit used to mount bunks onto PWT-800B, PWT-1000B, AND PWT-1100B trailer models.

MODEL: CFUBLT3/8X2.88Z

Used on

General

3/8″-16 x 3.06" x 2.38″ Zinc U-Bolt

This item is part of these kits:

- 2213B - Bunk Mounting Kit

- 2212B - Bunk Mounting Kit

- 2212B - Fender Mounting Kit

TIEDOWN: 83027Z

MODEL: CFUBLT3/8X2.38Z

Used on

General

6" x 1.5" x .25" Galvanized Flat Plate w/ 2 7/16" Holes and 4.5" Hole Centers - Shackle Link

- This item is part of the 2213G - Fender Mounting Kit used to mount Fenders to PWT-2213G, and PWT-2214G Trailer models.

MODEL: CFFLTSTRPFNDR(DBL)G

Used on

General

3/8"-16 x 1.56" x 3.63" Zinc U-Bolt - For Standard 1.5" SQ Tubing Axles

This item is part of the Zinc Axle Tie Plate Kit used to mount 2-Leaf Slipper Springs (550 lb), and 3-Leaf Slipper Springs (750 lb) to 1.5" Square Axle Tubing.

TIE DOWN MODEL: #83002Z

MODEL: CFAXLE-UBLT(1.5SQ-Z)

Used on

General

4" x 1" x .25" Zinc Flat Plate w/ 1/2" Holes and a 2.5" Hole Center - Shackle Link

- This item is part of the 1000B - Bunk Mounting Kit used to mount Bunk Boards onto PWT-800B, PWT-1000B, and PWT-1100B trailer models.

MODEL: CFFLTSTRPBUNK(SGL)Z

Used on