Part

General

Dry Launch SP7 Red Tail Light (Passenger Side) - Incandescent

The Dry Launch submersible 7-function passenger side tail light is waterproof with a bulb slide that has built-in dust, and splash guard. It snaps out for easy bulb replacement.

Dimensions:  W = 6"   H = 3.5"   D = 2-1/4"

Materials Include:

2 - 1/4″-18 Tail Light Bolt

2 - 1/4"-18 Zinc Nut

MODEL: CFLIGHTREAR(R)-INC(DL)

Optional for

ALL COM-FAB TRAILER MODELS

General

D.L. 12′ Winch Strap w/ Spring Loaded Hook and Loop End

Strap is generally sold as a replacement part for the Dutton-Lainson 900 lb Capacity Crank Winch (CFWNCH900DL). If you have a Com-Fab PWC trailer this is the replacement strap for your trailer's winch. The strap has the following capabilities:

- Strap working load limit: 1,700 lbs

- Break strength: 2,600 lbs

- 12' Long strap with hook

- Hand saver loop dimensions: 1" x 18"

- Steel hook tensile strength: 3,750 lbs

- Mounting bolt & nut dimensions: 2-3/4"-20 Hex Head Bolt, Zinc & 1/4"-20 Hex Head External Tooth Locknut, Zinc

MODEL: CFWNCHSTRAP-12FT(PWC)

Used on:

General

Dutton-Lainson 600LB Capacity Crank Winch

This item is a heavy duty winch used for horizontal pulling applications. It contains high carbon steel gears, permanently lubricated bearings, and a zinc Tuffplate(c) finish. A 12′ Winch Strap w/ Spring Loaded Hook and Loop End, and a Dutton-Lainson 900 lb Winch Handle.

The mounting materials are sold separately.

Recommended for Mounting (Com-Fab):

2 - 3/8-16 x 1" Hex Head Bolt, Zinc

2 - 3/8-16 Serrated Flange Hex Nut, Zinc

MODEL: CFWNCH600(DL)

Used on:

General

Dutton-Lainson 600 lb Winch Handle

This ergonomic handle attaches to a Dutton-Lainson 600 lb Capacity Crank Winch with 1/2" Nylock Nut.

DUTTON-LAINSON MODEL: #70304

MODEL: CFWNCHHANDLE-DL600

Used on

General

D.L. 1500LB Side Crank Swivel Jack

• Dutton-Lainson swivel marine tongue jack for boat and other trailer applications
• 1,500 lb. capacity
• 24-3/4" maximum tongue height
• Side wind handle with extra heavy screw drive and ergonomic handle grip
• Heavy duty polypropylene 8" diameter slotted wheel resists flat spots and cold weather cracking
• Zinc plated finish for additional rust resistance and longer life
• Easily swivels up for towing or down for stowing and locks in place in either position
• Reinforced wheel bracket for additional strength
• Includes all necessary bolt-on mounting hardware
• Made in the U.S.A.

Dutton-Lainson Model: 6850

MODEL: CFJACKSIDE-DL1500 (6850)

Used On

PT-/TT-2224
PT-/TT-2426

General

Dutton-Lainson 980 Coupler 2" Class 2 (3,500 lb) Zinc Plated 3″ Wide Tongue

This item mounts to all PWT-2213, and PWT-2214 trailer models with a Coupler Mounting Kit.

MODEL: CFCPLR(DL)-980

Specifications

Hole Diameter: 1/2"

Hole Distance: 2 1/2"

Hole Distance from Top: 5/8"

Hole Distance from Base: 1"

Used on

General

Flat Pontoon Bunk Bracket #44879

Length: 9.02"

Base Length: 8.38"

Width: 3"

Height: 5.25"

Optional for

General

Complete 545 Bolt 1250/1350LB Hub Assembly w/Bearings, Seal, Amp and Dust Cap - Dexter

Hub Includes:

- Triple Lip Grease Seal - 1.25" I.D. - 1.98"

- 1-1/16" Bearing Cup

- 1-1/16" L44649 Bearings

- 1-1/2"-20 Lug Nut Studs

- 1/2″-20 Lug Nut (Set of 5)

- 1.98" Dust Cap

- Super Lube Rubber Grommet

-Cotter Pin

- 12 Position Castle Nut

TIEDOWN MODEL: #46205X

MODEL: CFAXLE-HUB5BLT(1350-G)

Used on

General

Galvanized Angular Swivel Bracket - 7/16″ Top Hole

These are used to mount bunk boards onto all Jon Boat, and PWT Trailer models.

This item is part of these kits:

- 1000B - Bunk Mounting Kit

- 1000G - Bunk Mounting Kit

- 2212B - Bunk Mounting Kit

- 2212G - Bunk Mounting Kit

- 2213B - Bunk Mounting Kit

- 2213G - Bunk Mounting Kit

- Jon Boat Trailer Bunk Mounting Kit

- Jon Boat Trailer Bow Support Mounting Kit

- 'River Hawk' Jon Boat Trailer Bunk Mounting Kit

MODEL: CFBRKTSWIVEL

Used on

General

Axle Equalizer

Two of these axle equalizers are part of the Pontoon Boat Trailer Tandem Axle Mounting Kit used to mount 3-Leaf Double Eye Springs to frames on all Tandem Axle Setups for Pontoon Boat Trailers

MODEL: CFAXLE-EQUALIZER

Used on

General

Galvanized Bow Stop Bracket

This item is part of the Winch Poly Bow Roller Assembly used on every type of winch stand for all Jon Boat, and PWT trailer models.

MODEL: CFBRKTWNCHRLR

Used on

General

Galvanized Fender for Jon Boat, Canoe/Kayak Trailer and PWT-2212G Models

This fender is mounted to every Jon Boat Trailer, Kayak/Canoe Trailer and PWT-2212G models with a Jon Boat Trailer Fender Mounting Kit, and fits a 4.80 x 12″ C Load Range Galvanized Tire & Wheel.

MODEL: CFFNDRJBT/2212G

Used on

General

Galvanized Side Mount Spare Tire Carrier

• This item is optional for all of our Galvanized Trailer models.
• It can accommodate wheels from 10" to 16.5" with a spare tire.
• It fits all 4 and 5 lug wheels with 4" and 4.5" diameter hole patterns.
• The galvanized finish provides long lasting protection.
• The item can mount to trailer frames up to 3" wide and 4" high. 

*Used on Galvanized Trailer Models Only

TIEDOWN MODEL: #86098

MODEL: CFSTB-SIDE(G)

Installation Instructions

1. Using the spare tire carrier and spare tire as a guide, determine a suitable mounting location on trailer frame.

2. Slide U-bolt around the frame and through the holes in tire carrier.

3. Mount with flat washers, lock washers and nuts provided.

4. Using the spare tire to determine the correct holes to use, place the carriage bolts provided for mounting the spare tire in the holes of the rectangular plate. Bolt heads should be on the back side of the tire carrier. Secure bolts with “star” washers.

5. The mounting plate will accommodate several sizes of frames by using the various hole patterns.

6. Check position of the tire mount for proper clearance with the spare tire before tightening bolts.

7. Mount spare tire with 1/2" bolt, washers and hex nuts provided.

Optional for

ALL GALVANIZED TRAILER MODELS

General

Galvanized Single Axle Pontoon Boat Trailer Fender with Welded-On Spring Hangers

This fender with welded on spring hangers is mounted to a Pontoon Boat Trailer using a 2213G - Fender Mounting Kit, and typically uses a ST175/80R13 D Load Range 13″ Galv. Tire & Wheel. A 3500 lb Hydraulic Disc Brake Trailer Axle, or a 2900 lb Idler Trailer Axles is then mounted to the fender hangers using a Pontoon Boat Trailer Single Axle Mounting Kit.

MODEL: CFFNDRPT(SA-G)

Used on

General

Galvanized Winch Assembly Mounting Kit

This kit contains all of the requisite materials needed to mount a Galvanized Winch Assembly onto all Galvanized PWT trailer models.

Materials Include:

2 – 3/8″ x 3.06" x 4.5″ Galvanized U-Bolt

2 – 5" x 1.25" x .25" Galvanized Flat Plate

4 – 3/8″ Galvanized USS Flat Washer

4 – 3/8″-16 Galvanized Tri-Lock Hex Nuts

MODEL: CFWNCHKITG

Used on

General

Heavy Duty Pontoon Bunk Bracket #43747

This item is optional for all Pontoon Boat Trailer models. It fits 2' x 4' and 2' x 6' boards.

Specifications

Length: 15.4"

Base Length: 13.13"

Width: 3"

Height: 6.07"

Optional for

Heavy safety/breakaway chain for pontoon trailers. (1X) 1/4x31IN 5000LB Capacity Safety Chain w/ 7/16IN Hook & Latch, Grade 30

SKU: CFSFTYCHN-5K (HVY)

Used on all pontoon trailer models

General

Jammy J-51-A 3/4" Single Diode PC Side Marker Light

The Jammy diode side marker light is a 3/4″ Round Single Diode, Amber-Colored LED Marker Light (PC Rated) that mounts in 3/4″ diameter holes. This model includes a mounting grommet, and 6″ leads with blunt cut ends.

MODEL: CFLIGHTSDMRKR-LED(J-51-A)

General

Jon Boat Trailer Bow Support Bunk Mounting Kit

These are all of the requisite materials needed to mount a 2″ x 4″ x 2′ Black Marine Carpeted Bow Support Bunk onto all Jon Boat Trailer models.

Materials Include:

1 – 3/8″ x 3" x 4.5″ Galvanized U-Bolt

2 – 8″ Galvanized Adjustable Bolster Bunk Bracket

2 – 3/8″-16 x 1″ Galvanized Hex Head Bolts

2 – Galvanized Angular Swivel Bracket

4– 3/8″-16 Galvanized Tri-Lock Hex Nut

4 – 3/8″ Galvanized Flat Washer

4 – 5/16" x 1-1/2″ Galvanized Hex Head Lag Screw

1 - 5" x 1.25" x .25" Galvanized Flat Plate w/ 9/16" Holes

MODEL: CFBNKKIT-BOWSPRT

Used on

General

Jon Boat Trailer Bunk Mounting Kit

This kit contains all of the requisite materials needed to mount a 2″ x 4″ x 6′ Black Marine Carpeted Bunk Board onto every Jon Boat Trailer model. 

Materials Include:

2 – 3/8″-16 x 3.06" x 2.38″ Galvanized U-Bolt

2 – 8″ Adjustable Bolster Bunk Bracket

2 – 3/8″-16 x 1" Galvanized Hex Head Bolt

2 – Galvanized Angular Swivel Bracket

6 – 3/8″-16 Galvanized Tri-Lock Nut

6 – 3/8″-16 Galvanized Flat Washer

4 – 5/16" x 1-1/2″ Galvanized Hex Head Lag Screw

MODEL: CFBNKKIT-JBT

Used on

General

Jon Boat Trailer Fender Mounting Kit

These are all of the requisite materials needed to mount a Galvanized Fender 4.80 x 12” Tire onto every Jon Boat Trailer model.

Materials Include:

2 – 3/8″-16 x 3.06" x 2.38″ Galvanized U-Bolt

2 – 5" x 1.25" x .35" Galvanized Flat Plate

4 – 3/8" Galvanized Flat Washer

4 – 3/8" Galvanized Tri-Lock Nut

MODEL: CFFNDRKIT-JBT

Used on

General

Jon Boat Trailer Winch Assembly Mounting Kit

This kit contains all of the requisite materials needed to mount a 32" Galvanized Winch Assembly w/DL 600 onto all Jon Boat Trailer models.

Materials Include:

2 – 3/8″ x 3.06" x 5.25″ Zinc U-Bolt

2 – 5" x 1.25" x .25" Galvanized Flat Plate

4 – 3/8″-16 Serrated Zinc Flange Nuts

MODEL: CFWNCHKIT-(JBT)

Used on

General

TecNiq License Plate Bracket

TECNIQ MODEL: L95-0B00-1

MODEL: CFTAG-TEC

Used on

ALL COM-FAB TRAILER MODELS

General

Locking Spare Tire Bracket, fits 3″ Width Tubing

This item is used to lock down, and transport a spare tire on all Com-Fab trailer models. Lock not included.

MODEL: CFSTB-TOP

Optional for

ALL COM-FAB TRAILER MODELS