Part

General

- Two of these are used with 1/4″ Zinc Nuts to mount TecNiq 8 Function 6" LED Tail Lights & TecNiq 7 Function 6" LED Tail Lights to all current Com-Fab Trailer Models

- Two of these are used with 1/4″ Zinc Nuts to mount Dry Launch Submersible Tail Lights to Pre-2018 Com-Fab trailer models.

MODEL: CFBLTLIGHT

Used On

ALL COM-FAB TRAILER MODELS

General

1/4″-20 Thread External Tooth Locknut, Zinc Nut for Tail Lights

- Two of these are used with 1/4″- 20 Tail Light Bolts to mount TecNiq 8 Function 6" LED Tail Lights to all current Com-Fab Trailer models.

- Two of these are used with 1/4″- 20 Tail Light Bolts to mount Dry Launch SP7 Red Tail Lights to all Pre-2018 Com-Fab trailer models.

- One of these is used w/ 2-3/4"-20 Thread Bolts to secure PWT winch strap to crank winch.

MODEL: CFNUT1/4LOCKZ

Used on

ALL COM-FAB TRAILER MODELS

General

15' 4-Pin Wire Harness Assembled w/ Protective Sleeve

The wiring is pulled through the PWT-800 trailer frame to provide connection between the lighting and the vehicle. It connects to the vehicle with a 4-Pin Male Connector. This item comes with a 3/8 20" Protective Sleeve and 30" Ground with 1/2" ring terminal.

MODEL: CFWH14

Used on

General

17' 4-Pin Wire Harness Assembled w/ Protective Sleeve

The wiring is pulled through the trailer frame to provide connection between the lighting and the vehicle. It connects to the vehicle with a 4-Pin Male Connector. This item comes with a 3/8 20" Protective Sleeve and 30" Ground with 1/2" ring terminal.

MODEL: CFWH16

Used on

General

21' 4-Pin Wire Harness Assembled w/ Protective Sleeve

The wiring is pulled through the trailer frame to provide connection between the lighting and the vehicle. It connects to the vehicle with a 4-Pin Male Connector. This item comes with a 3/8 20" Protective Sleeve and 30" Ground with 1/2" ring terminal.

MODEL: CFWH21

Used on

JBT-1600 ‘RIVER HAWK’

General

35' 4-Pin Wire Harness Assembled w/ Protective Sleeve

The wiring is pulled through the trailer frame to provide connection between the lighting and the vehicle. It connects to the vehicle with a 4-Pin Male Connector. This item comes with a 3/8 20" Protective Sleeve and 30" Ground with 1/2" Ring Terminal.

MODEL: CFWH35

Used on

General

Dry Launch Amber Side Marker Light w/ 10" of Wire

This item is a Dry Launch 203 Series with a snap out bulb slide. You can change the bulb without tools, and mount it with a single stud. It can be used as a Side Marker Light for the tongue of all Pontoon Boat Trailer models.

MODEL: CFLIGHTSDMRKR-10

Optional for

General

Dry Launch SP7 Red Tail Light (Driver Side) - Incandescent

The Dry Launch submersible 8-function driver side tail light is waterproof with a bulb slide that has a built-in dust and splash guard. It snaps out for easy bulb replacement.

Dimensions:  W = 6"   H = 3.5"   D = 2-1/4"

Materials Include:

2 - 1/4″ - 18 Tail Light Bolt

2 - 1/4" -18 Zinc Nut

MODEL: CFLIGHTREAR(L)-INC(DL)

Optional for

ALL COM-FAB TRAILER MODELS

General

Dry Launch SP7 Red Tail Light (Passenger Side) - Incandescent

The Dry Launch submersible 7-function passenger side tail light is waterproof with a bulb slide that has built-in dust, and splash guard. It snaps out for easy bulb replacement.

Dimensions:  W = 6"   H = 3.5"   D = 2-1/4"

Materials Include:

2 - 1/4″-18 Tail Light Bolt

2 - 1/4"-18 Zinc Nut

MODEL: CFLIGHTREAR(R)-INC(DL)

Optional for

ALL COM-FAB TRAILER MODELS

General

J-71 Jammy Marine LED Submersible Tail Light (Passenger)

The J-71 Jammy Marine LED submersible tail light is an LED low profile submersible combination lamp for over 80″ Wide Trailers. These LED lamps come with 13, and 17 Diode Configurations for 7 or 8 function use as Stop/Turn Light, Tail Light, Rear Clearance Light, Side Marker Light, Rear Reflex Reflector and Side Reflex Reflector. Includes two 7/16" nuts and bolts. They use marine grade tinned wire, and double epoxy sealed design with the lowest profile of any combination lamp on the market for protection against harsh salt water environments.

MODEL: CFLIGHTREAR(R)-LED(JAM)

Specifications

Dimensions: 6-1/4” L x 3-3/4” W x 1-7/8” H

Wiring: 8″ leads with ground ring terminal

Mount: 2 Stainless Studs w/ Supplied Nuts

Optional for

ALL COM-FAB TRAILER MODELS

General

J-71-L Jammy Marine LED Submersible Tail Light (Driver Side)

The J-71-L Jammy Marine LED Submersible Tail Light(Left) is an LED low profile submersible combination lamp for over 80″ Wide Trailers.  The lamp comes with 13, and 17 Diode Configurations for 7 or 8 function use as Stop/Turn Light, Tail Light, Rear Clearance Light, Side Marker Light, Rear Reflex Reflector, and Side Reflex Reflector. It comes with 7/16" nuts and bolts for mounting. They use Marine Grade Tinned Wire, and Double Epoxy Sealed Design, with the lowest profile of any combination lamp on the market for protection against harsh salt water environments.

MODEL: CFLIGHTREAR(L)-LED(JAM)

Specifications

Dimensions: 6-1/4” L x 3-3/4” W x 1-7/8” H

Wiring: 8″ leads with ground ring terminal

Mount: 2 Stainless Studs w/ Supplied Nuts

Optional for

ALL COM-FAB TRAILER MODELS

General

Jammy J-51-A 3/4" Single Diode PC Side Marker Light

The Jammy diode side marker light is a 3/4″ Round Single Diode, Amber-Colored LED Marker Light (PC Rated) that mounts in 3/4″ diameter holes. This model includes a mounting grommet, and 6″ leads with blunt cut ends.

MODEL: CFLIGHTSDMRKR-LED(J-51-A)

General

TecNiq Red LED V-Shaped Light Bar w/ 58" Lead

• Used on all Double PWT Trailer models.
• Screws included with purchase
• Fully submersible LED Identification bar
• TecSeal Urethane Potting - Guaranteed Circuit Board Protection
• Durable impact resistant lens
• Available in colored or clear impact resistant lens
• IP68 rating while exceeding FMVSS 108 standards
• Reliable performance over 100,000 hours

MODEL: CFLIGHTBAR-LED(V-TEC)

Used On

General

Red Low Profile ID Light Bar w/ Ground Terminal

• Used on all Pontoon Trailer models
• Screws included with purchase
• Meets all FMVSS 108 requirements for wide and narrow vehicles
• IP68 Rated - Dust and water proof with hermetic seal
• TecSeal Urethane Potting - Guaranteed Circuit Board Protection
• Durable impact resistant lens
• Excellent UV Resistance - Automotive exterior lighting grade polycarbonate
• Reliable performance over 100,000 hours
• Can be mounted horizontal, vertical, or at any angle

TecNiq Model No. T10-RR00-1

MODEL: CFLIGHTBAR-LED(S-TEC)

Used On

General

TecNiq-S14 Amber LED Mini PC Side Marker Light with 24" Lead

• Comes with a 1/4" Nut.
• Brilliant illumination in a compact size
• IP 68 Rated - Dust and water proof
• TecSeal Urethane Potting - Guaranteed Circuit Board Protection
• Stud-mounted, no visible fasteners
• Reliable performance over 100,000 hours
• Vertical mount positions meets P2 specifications, while horizontal mount meets PC specifications 

Tecniq Part No. S14-AAS0-1

MODEL: CFLIGHTSDMRKR-LED(TEC-A24)

Used on 

• Comes with a 1/4" Nut.
• Brilliant illumination in a compact size
• IP 68 Rated - Dust and water proof
• TecSeal Urethane Potting - Guaranteed Circuit Board Protection
• Stud-mounted, no visible fasteners
• Reliable performance over 100,000 hours
• Vertical mount positions meets P2 specifications, while horizontal mount meets PC specifications 

TecNiq Part No. S14-RRS1-1

MODEL: CFLIGHTSDMRKR-LED(TEC-R24)

Used on 

General

TecNiq-T86 7 Function 6" Box LED Passenger Side Tail Light w/ Pigtail

• These are optional for all Trailer Models.
• Multi-Function 6" Box Tail Light
• Urethane Potting w/ Guaranteed Circuit Board Protection
• Dust and water proof with hermetic seal
• Durable impact resistant lens
• Meets all FMVSS 108 requirements for narrow and wide vehicles
• Reliable performance over 100,000 hours
• Fits standard mounting as a direct replacement
• Functions include: Stop, Turn, Tail, Clearance, Side marker, Side Reflector,
  Rear Reflector, and License Plate Light (Left)

Includes two 7/16" bolts w/ nuts for mounting.

MODEL: CFLIGHTREAR(R)-LED(TEC)

Used on

ALL COM-FAB TRAILER MODELS

General

TecNiq-T86-L 8 Function 8" Box Driver Side Tail Light w/ Pig Tail.

• Multi-Function 6" box tail light
• Urethane Potting w/ Guaranteed Circuit Board Protection
• Dust and water proof with hermetic seal
• Durable impact resistant lens
• Meets all FMVSS 108 requirements for narrow and wide vehicles
• Reliable performance over 100,000 hours
• Fits standard mounting as a direct replacement
• Functions include: Stop, Turn, Tail, Clearance, Side marker, Side Reflector,
  Rear Reflector, and License Plate Light (Left)

Includes two 7/16" bolts w/ nuts for mounting.

MODEL: CFLIGHTREAR(L)-LED(TEC)

Used on

ALL COM-FAB TRAILER MODELS