PWT-1100G Parts

General

Dry Launch SP7 Red Tail Light (Passenger Side) - Incandescent

The Dry Launch submersible 7-function passenger side tail light is waterproof with a bulb slide that has built-in dust, and splash guard. It snaps out for easy bulb replacement.

Dimensions:  W = 6"   H = 3.5"   D = 2-1/4"

Materials Include:

2 - 1/4″-18 Tail Light Bolt

2 - 1/4"-18 Zinc Nut

MODEL: CFLIGHTREAR(R)-INC(DL)

Optional for

ALL COM-FAB TRAILER MODELS

General

Locking Spare Tire Bracket, fits 3″ Width Tubing

This item is used to lock down, and transport a spare tire on all Com-Fab trailer models. Lock not included.

MODEL: CFSTB-TOP

Optional for

ALL COM-FAB TRAILER MODELS

General

TecNiq-T86 7 Function 6" Box LED Passenger Side Tail Light w/ Pigtail

• These are optional for all Trailer Models.
• Multi-Function 6" Box Tail Light
• Urethane Potting w/ Guaranteed Circuit Board Protection
• Dust and water proof with hermetic seal
• Durable impact resistant lens
• Meets all FMVSS 108 requirements for narrow and wide vehicles
• Reliable performance over 100,000 hours
• Fits standard mounting as a direct replacement
• Functions include: Stop, Turn, Tail, Clearance, Side marker, Side Reflector,
  Rear Reflector, and License Plate Light (Left)

Includes two 7/16" bolts w/ nuts for mounting.

MODEL: CFLIGHTREAR(R)-LED(TEC)

Used on

ALL COM-FAB TRAILER MODELS

General

2″ Steel Super Lube Grease Dust Cap & Plug for Axle Hub

This item is a part of all hub assemblies and comes as a pair.

Galvanized 5-Bolt Hub Assembly

Powder Coated Black 5-Bolt Hub Assembly

TIE DOWN MODEL: #17093

MODEL: CFAXLE-CAP&PLUG

Used on

ALL COM-FAB TRAILER MODELS

General

Dry Launch SP7 Red Tail Light (Driver Side) - Incandescent

The Dry Launch submersible 8-function driver side tail light is waterproof with a bulb slide that has a built-in dust and splash guard. It snaps out for easy bulb replacement.

Dimensions:  W = 6"   H = 3.5"   D = 2-1/4"

Materials Include:

2 - 1/4″ - 18 Tail Light Bolt

2 - 1/4" -18 Zinc Nut

MODEL: CFLIGHTREAR(L)-INC(DL)

Optional for

ALL COM-FAB TRAILER MODELS

General

4.80 x 12″ C Load Range Galvanized Finish Tire & Wheel, Bias - Kenda/Loadstar

This is the tire and wheel used on PWT-800G, PWT-1000G, PWT-1100G, PWT-2212G, and all Jon Boat Trailer models. Tire Capacity is 990lbs (450kg). Speed rating 81 mph.

MODEL: CFT48012G

Used on

General

12′ Winch Strap w/ Spring Loaded Hook and Loop End

Strap is generally sold as a replacement part for the Dutton-Lainson 900 lb Capacity Crank Winch (CFWNCH900DL). If you have a Com-Fab PWC trailer this is the replacement strap for your trailer's winch. The strap has the following capabilities:

- Strap working load limit: 1,700 lbs

- Break strength: 2,600 lbs

- 12' Long strap with hook

- Hand saver loop dimensions: 1" x 18"

- Steel hook tensile strength: 3,750 lbs

- Mounting bolt dimensions: 2-1/2" x 1/4" bolt

MODEL: CFWNCHSTRAP-12FT(PWC)

Used on

General

1500 lb Galvanized PWC Trailer Axle w/ 545 Hubs and Springs

*NOTE: If your trailer is older than 2006, call before ordering to ensure you receive the correct axle*

Materials Include:

1 - 44.5" x 1.5" x 1.5" x 11 Gauge Galvanized Axle Tubing 

2 - Galvanized 5-Bolt Hub Assembly

2 - 3-Leaf Slipper Springs (750 lb)

1 - Galvanized Tie Plate Kit

This item is mounted to the PWT-1000G, and PWT-1100G trailer models with a Galvanized Axle Mounting Kit.

MODEL: CFAXLE1500G

Specifications

Tubing: 1.5" Galvanized Square Axle

Load Rating: 1500 lb

Hub Face: 50.5"

Spring Center: 41.188"

Overall Length: 56"

Bearing Size: 1-1/16"

Used on

General

Winch Poly Bow Roller Assembly

This kit is part of every Winch Assembly used on every PWT, and Jon Boat Trailer model. 

Materials Include:

1 – Galvanized Bow Stop Bracket

1 – 3/8″-16 x 3.75″ Zinc Hex Head Cap Bolt

1 – 3/8″-16 Zinc Hex Flange Top Lock Nut

1 – 1/2″-13 x 4.5″ Zinc Hex Head Cap Bolt

1 – 1/2″-13 Zinc Top Lock Nut

1 – 3″ Amber Poly Bow Roller

2 – 3″ Amber Poly Bow Roller Bell End

2 – 1/2″- Zinc Flat Washer

MODEL: CFASSM-WNCHRLR(3)

Used on

General

Dutton-Lainson 900 lb Capacity Crank Winch

This item is a heavy duty winch used for horizontal pulling applications. It contains high carbon steel gears, permanently lubricated bearings, and a zinc tuffplate finish. A 12′ Winch Strap w/ Spring Loaded Hook and Loop End, and a Dutton-Lainson 900 lb Winch Handle. The mounting materials are sold separately.

Mounting Kit Includes:

2 - 3/8"-16 x 1" Zinc Hex Head Cap Bolt

2 - 3/8"-16 Serrated Zinc Flange Nuts

MODEL: CFWNCH900DL

Used on

General

1200 lb Side Crank Swivel Jack

This item fits 3″ x 5“ tongues. It comes with a 1200 lb Side Crank Swivel Jack Mounting Kit.

MAXIMUM CAPACITY: 1200LB

PACIDIC RIM MODEL: MJ-1200B

MODEL: CFJACKSIDE

Used on

General

TecNiq License Plate Bracket

TECNIQ MODEL: L95-0B00-1

MODEL: CFTAG-TEC

Used on

ALL COM-FAB TRAILER MODELS

General

14″ Galvanized Winch Assembly w/ DL 600 lb Winch

This assembly includes a 14" Galvanized Winch Post, a Dutton-Lainson 600 lb Capacity Crank Winch, a Winch Poly Bow Roller Assembly, and a Galvanized Winch Assembly Mounting Kit. When mounted, the standard height for the bow roller is 12", but it can be adjusted to accommodate your particular boat.

Mounting Hardware Includes:

4 – 3/8″-16 Galvanized Tri-Lock Hex Nuts

MODEL: CFWNCH1000G

Used on

General

17' 4-Pin Wire Harness Assembled w/ Protective Sleeve

The wiring is pulled through the trailer frame to provide connection between the lighting and the vehicle. It connects to the vehicle with a 4-Pin Male Connector. This item comes with a 3/8 20" Protective Sleeve and 30" Ground with 1/2" ring terminal.

MODEL: CFWH16

Used on

General

Complete 545 Bolt 1250/1350LB Hub Assembly w/Bearings, Seal, Amp and Dust Cap - Dexter

Hub Includes:

- Triple Lip Grease Seal - 1.25" I.D. - 1.98"

- 1-1/16" Bearing Cup

- 1-1/16" L44649 Bearings

- 1-1/2"-20 Lug Nut Studs

- 1/2″-20 Lug Nut (Set of 5)

- 1.98" Dust Cap

- Super Lube Rubber Grommet

- Cotter Pin

TIEDOWN MODEL: #46205X

MODEL: CFAXLE-HUB5BLT(1350-G)

Used on

General

Galvanized Tie Plate Kit for 1.5" Square Trailer Axles

This kit is used to mount springs to Galvanized 1.5" Square Trailer Axles. The kit is a part of the 1500 lb Galvanized Trailer Axle used on every PWT-1000G, and PWT-1100G trailer model. It is also part of the 1500 lb Extended Galvanized Trailer Axle used on both PWT-2212 trailer models.

Materials Include:

2 - Galvanized Axle Tie Plate for 1.5" Square Trailer Axle

4 - 3/8"-16 x 1.56" x 3.63" Galvanized U-Bolt

8 - 3/8"-16 Galvanized Tri-Lock Nut

8 - 3/8" Galvanized Lock Washer

MODEL: CFAXLEKIT-SPRNGMNT(1.5K-G)

Used on

General

RAM 2″ (Class 2) Zinc Plated Coupler fits 3″ Wide Tongue

This item is mounted to PWT-800, PWT-1000, PWT-1100, PWT-2212, and all Jon Boat Trailer models with a Coupler Mounting Kit

MODEL: CFCPLR(RAM)-3x2

Specifications

- Hole Diameter: 1/2"

- Hole Distance: 2 1/2"

- Hole Distance from Top: 7/8"

- Hole Distance from Base: 1"

Used on

General

Galvanized Angular Swivel Bracket - 7/16″ Top Hole

These are used to mount bunk boards onto all Jon Boat, and PWT Trailer models.

This item is part of these kits:

- 1000B - Bunk Mounting Kit

- 1000G - Bunk Mounting Kit

- 2212B - Bunk Mounting Kit

- 2212G - Bunk Mounting Kit

- 2213B - Bunk Mounting Kit

- 2213G - Bunk Mounting Kit

- Jon Boat Trailer Bunk Mounting Kit

- Jon Boat Trailer Bow Support Mounting Kit

- 'River Hawk' Jon Boat Trailer Bunk Mounting Kit

MODEL: CFBRKTSWIVEL

Used on

General

3/8"-16 Zinc Hex Flange Top Lock Nut Zinc

This item is part of the:

– 1000B - Bunk Mounting Kit

– 2212B - Fender Mounting Kit

– 2213B - Fender Mounting Kit

– Winch Poly Bow Roller Assembly

– Pontoon Boat Trailer Winch Assembly

MODEL: CFNUT3/8LOCKZ

Used on

ALL COM-FAB TRAILER MODELS

General

1000/1100G - Bunk Mounting Kit

These are all of the requisite materials needed to mount a 2″ x 4″ x 6′ Carpeted Black Marine Bunk Board onto PWT-1000G trailer models, as well as a 2″ x 4″ x 7′ Black Marine Carpeted Bunk Board onto a PWT-1100G trailer model.

4 – 5/16" x 1-1/2″ Galvanized Hex Head Lag Screw

MODEL: CFBNKKIT-1000/1100G

Used on

General

3/8"-16 x 2.06" x 2.88" Galvanized U-Bolt

This item is part of the 1000G Bunk Mounting Kit used to mount bunks to PWT-800G, PWT-1000G, AND PWT-1100G trailer models.

MODEL: CFUBLT3/8X2.88G

Used on

General

5/16″ x 1-1/2″ Galvanized Hex Head Lag Screw

It is used for mounting Bunk Boards to Galvanized Angular Swivel Brackets, and Pontoon Boat Trailer Bunk Brackets on all trailer models.

MODEL: CFSCRWLAG-5/16-0150

Used on

ALL COM-FAB TRAILER MODELS

General

4" x 1" x .25" Galvanized Flat Plate w/ 2 1/2" Holes and a 2.5" Hole Center - Shackle Link

- This item is part of the 1000G - Bunk Mounting Kit to mount Bunk Boards onto PWT-800G, PWT-1000G, and PWT-1100G trailer models.

- This item is part of the Tall Galvanized Bunk Bracket Kit used to mount mount 2″ x 4″ or 2″ x 6″ bunk boards on all Pontoon Boat Trailer models.

MODEL: CFFLTSTRPBUNK(SGL)G

Used on

General

Galvanized Axle Mounting Kit

This kit is used to mount Complete Galvanized Axles to all PWT, and Jon Boat Trailer models.

Materials Include: 

2 - 1/2" x 3" Galvanized Hex Head Bolt

2 - 1/2"-13 Galvanized Tri-Lock Nuts

MODEL: CFAXLEMNTKITG

Used on